Recent content by ChrisOIFdoc
-
-
Anyone tow a 7000lb camper?
Only if my mother in law is being towed behind my truck on the way to camp. Does that count?- ChrisOIFdoc
- Post #16
- Forum: Towing & Hauling
-
3.5 inch bodylift install question
Keep an eye on the shift cable, anything connected to the body and frame ( wires, hoses, etc. ), You will need to remove the lower portion of the fan shroud. Can't remember everything bcuz it's been a few years since I did mine. Wasn't too much though.- ChrisOIFdoc
- Post #5
- Forum: 1st Gen - 1997 - 2002
-
3.5 inch bodylift install question
Fuel fill hose will interfere with the frame past 2" 1/2 inches of body lift. Mine is touching the frame and I used double stacked hockey pucks for my body lift.- ChrisOIFdoc
- Post #4
- Forum: 1st Gen - 1997 - 2002
-
2000 Expy EB 4x4.....looking for info on lifting Eddie up some more
Torsion keys plus rear coils for 2" 1/2 lift. Double stacked hockey puck body lift for another 2" 1/2 lift. I have 38" tires on her now- ChrisOIFdoc
- Post #2
- Forum: 1st Gen - 1997 - 2002
-
-
Let’s see your camping/adventure/overland build
Here’s mine- ChrisOIFdoc
- Post #2
- Forum: General Discussion
-
2002 Expy stuck in 4High
I responded to you on the other thread. Check it out- ChrisOIFdoc
- Post #3
- Forum: 1st Gen - 1997 - 2002
-
Transfer case problems!!
I’ll try to help. What tricks have you tried? Are you sure the selector switch is working? Can you, or have you pulled the shift motor and cycled through the selector options to ensure the motor is doing what it needs to? If you want, you can send me a private message and I’ll give you my...- ChrisOIFdoc
- Post #10
- Forum: 1st Gen - 1997 - 2002
-
Transfer case problems!!
Did you get it worked out?- ChrisOIFdoc
- Post #8
- Forum: 1st Gen - 1997 - 2002
-
Transfer case problems!!
You bet. DM me if you want me to swing by. I’m on call and will need to go to ABQ anyway.- ChrisOIFdoc
- Post #7
- Forum: 1st Gen - 1997 - 2002
-
Transfer case problems!!
To prevent giving you bad advice. If the axle nut isn’t holding the bearing pack together it should be ok. I have 99 but I can’t remember for sure what it looks like. I’m in Rio Rancho. Are you in ABQ? I may be able to swing by- ChrisOIFdoc
- Post #5
- Forum: 1st Gen - 1997 - 2002
-
Transfer case problems!!
Remove both cv’s and go for a drive. Could be the front brake, front diff, wheel bearing etc. It’s a start anyway. What year is your expy?- ChrisOIFdoc
- Post #2
- Forum: 1st Gen - 1997 - 2002
-
Questions about Compatibility of putting a 2003 engine into a 1998
Heli-coil not believe coil. Stupid phone- ChrisOIFdoc
- Post #7
- Forum: 1st Gen - 1997 - 2002
-
Questions about Compatibility of putting a 2003 engine into a 1998
I had an 05 expedition. 3 valve motor was a constant pain in the a$$. Cam phaser issues were constant. I finally disconnected the left bank sensor, ran it for two years that way with the check engine light on. I gave up the horsepower just so I didn’t have to listen to bb’s rattling in a can at...- ChrisOIFdoc
- Post #6
- Forum: 1st Gen - 1997 - 2002
