Recent content by mwhyes

  1. M

    Changing Plugs/COPs

    Ah. I didn't catch these instructions. I don't plan on diving back in to the engine to do the job again, so unless any issues pop up....is what it is.
  2. M

    Changing Plugs/COPs

    I surprisingly had no issues with plugs or packs - they all came out relatively easily (5.4l 2v). This is correct. I actually went up a hair to 18 as these plugs are known to walk out of their threads. The yellow Accel 140032 ones from Amazon, approximately $150 for 8. Motorcraft SP-479...
  3. M

    going for tail light mods

    The place i have seen the mod done is the same thread as the guy who did the 3rd gen facelift on his 2nd gen. http://www.expeditionforum.com/f27/how-modify-07-expy-taillights-fit-03-06-expys-7128/ Here are some more links to discussions...
  4. M

    Changing Plugs/COPs

    Just completed. Took 4 hours - it was hot and humid in DC these last few days, so a lot of sweating and rest breaks. It wouldn't have kicked my butt so hard if it were cooler out. It's an intuitive job, but just hard to wiggle around in there. If every cylinder was like #1, it would take less...
  5. M

    Changing Plugs/COPs

    Cool, thanks. I did pick up a 7mm u-joint socket from Amazon a few weeks ago in anticipation of the work, so I hope that will be helpful. Thanks again.
  6. M

    Changing Plugs/COPs

    Thank you for the note - I plan on doing this myself within the next week or to. I'm at 126k. Did you have to remove anything other than the air intake?
  7. M

    Replace broken tail lights with LED ones? Which is better.

    No comment to your aftermarket question, but I believe you can also use the '07 and up Expedition taillights with very little modification. Slightly updated, but still OEM look, which I prefer.
  8. M

    2nd Gen Newb Questions

    Related to your wind noise - I want to share my trucks situation: I have a problem with driver side window noise. When you roll the window down at highway speed it will not roll up and seal fully. It will seal up from rain, but it will cause wind noise. I have to slow down to under 20-30mph for...
  9. M

    4r70w fluid change

    Sorry for the wrong information - that is good to know! In some respects 5 qt's may by a good thing as you wont be "shocking" the tranny with all new fluid, but what do I know!
  10. M

    4r70w fluid change

    I just checked, I think you'll be fine - Section 307-01B in the shop manual for the 2003 Expedition (free version posted earlier this month) on p2183 specifically states removing the drain plug on the torque converter as a defined step in draining the tranny fluid. I realize you have a 2004...
  11. M

    4r70w fluid change

    Yes, pop off the rubber grommit below the bellhouse. Manually spin the crank pulley to line up drain hole to face downward. Google for complete directions, but this should get you started: https://www.youtube.com/watch?v=iDH9idLuSPA
  12. M

    Front Grill question....

    Noticed the same thing - I bought and painted a lower grill for my XLT. Subtle, but much better looking than the stock hole. Cost $20-30 and took a half hour. There are even holes in the XLT grill to receive clips. Take a look at my album.
  13. M

    03 EB drivers window issues...

    if the motor and switch is functioning, there is likely an issue with the cabling and winding device. It is all string driven, so if the wire is off the pullys, or the winding mechanism is not wrapped correctly, it will not pull. I just had this issue with my rear passenger door, and I just...
  14. M

    Hello from Arlington VA

    thanks for the feedback - I'll do a lil homework on the relay.
  15. M

    Hello from Arlington VA

    Greetings from DC! Picked up a blue 2003 XLT 4x4 from a family in the suburbs. DD is a 6 speed Infiniti G37 coupe, which is great car, but is very useless for any task, and only good for summer. Been a Nissan guy my whole life (Xterra, Maxima, Infiniti G), part prices are hit or miss, but...
Top