Search results
-
Freezing Doors And Windows...
FYI, I used Pam cooking spray from my wifes pantry, wiped all the seals with a rag soaked in it, haven't had a stuck door since. Found the idea online somewhere, seems to work for doors frozen to the seals- Tuner710
- Post #22
- Forum: General Discussion
-
1998 Expedition Air Suspension Issues
Sooter6 had a post showing exactly how to disable the light. Involves cutting wire or wires under the dash, worked for mine. Try a search on this forum. Good luck- Tuner710
- Post #19
- Forum: 1st Gen - 1997 - 2002
-
need 3rd row seat measurement, please
Hit by Thunder, Mine is a 98 with rear AC, measurements are as follows: 47" wide measured across the plastic hinge covers for the seatback 16" approx center of the mounting pockets in the floor, side to side 17" approx center of the mounting pockets in the floor, front to back Hope that...- Tuner710
- Post #3
- Forum: 1st Gen - 1997 - 2002
-
Can i tow this? 98 expy 5.4L
Agree with all of the above. I tow 4000 lb with a 1998 with 170,000 miles on the rig. The most important thing about towing your boat will likely be stopping ability. Check and make sure trailer brakes are working and in excellent condition. My neighbor once told me a story about losing his...- Tuner710
- Post #5
- Forum: 1st Gen - 1997 - 2002
-
How high is your frame off the ground?
Mine sits at 9 1/2" to the skid plate under the gas tank. 1998 Expy 4X4 converted from air ride to springs and coilovers, with stock 265 / 70's. Hope thaat helps- Tuner710
- Post #3
- Forum: 1st Gen - 1997 - 2002
-
Trouble with rear door actuator, has anyone replaced these?
Rear passenger Yes, when I bought my 98 the rear passenger lock didnt work. I took the panel off and felt around in there and found the actuating rod laying in the bottom of the door. Turns out the plastic connector has 2 ears on it that were broken off. No response from Dorman on a replacement...- Tuner710
- Post #4
- Forum: 1st Gen - 1997 - 2002
-
-
battery draw
I had a similar problem, only it would have a flat battery in 3 days if I didn't start it before then just to charge it up. Did a lot of troubleshooting, checking wire bundles and connections, even pulling fuses and checking draw with a fluke meter on each circuit on the advice of the...- Tuner710
- Post #6
- Forum: 1st Gen - 1997 - 2002
-
Air Suspension
Good Post! That post would make a good sticky. If I hadn't already converted over from 4 corner air, you would have sold me on it Buddy!- Tuner710
- Post #3
- Forum: 1st Gen - 1997 - 2002
-
fuel system cleaner
For what its worth, the pusher at my local Autozone is big on Lucas additive. I use it about once a year in 3 vehicles just as maintenance for injectors.- Tuner710
- Post #5
- Forum: 1st Gen - 1997 - 2002
-
Air Suspension conversion done
Chipete, sorry didnt take any pictures during the process..kinda wish I had now, but was focused on getting the parts swapped! I dont think the boat will be a problem, havent hooked it up yet cause its still snowing out here in the west. But around 400 pounds of tongue weight shouldnt squat...- Tuner710
- Post #8
- Forum: Suspension
-
Air Suspension conversion done
Chipete, I gained about an inch of ride heigth. My front pass shock was blown, rear air bags good but the stock gas shocks were both shot. Real happy with the swap. Mine from Advance Auto online, $248.00 due to 15% discount and free shipping. Expeditionary, how did you get the 3rd row facing...- Tuner710
- Post #7
- Forum: Suspension
-
Air Suspension conversion done
Hi all. Been lurking here and getting LOTS of good tips on a lot of work on my 1998 Expy. Figured it is time to pay it back! A few tips I kept track of as I went along withy the Monroe 90010 kit: Soak all hardware before starting. Mark your keyed bolts on upper control arms, so you can put...- Tuner710
- Thread
- Replies: 16
- Forum: Suspension
