Search results

  1. M

    So here's a new one...

    Ok, final update... My vacuum holds very well. Occasionally I'll leave my hvac set on something other than "off" for the 12+ hours that I'm at work. I'll notice and turn it to off before cranking the engine. I'll actually hear the vacuum release pressure (all before the key is in the...
  2. M

    So here's a new one...

    Ok.. So an update.... Could not find any vacuum leaks. On a hunch that air is trapped, I parked on my semi-steep driveway. I jacked up the driver front wheel and let it run for an hour and a half with reservoir cap off and heat on high to get very hot air from the vents. I lowered the truck...
  3. M

    So here's a new one...

    Wow, thanks for the help Stoned and Bedrck. I will check for a vacuum leak.
  4. M

    So here's a new one...

    The fact that it happens under load has me wondering if electrolysis has anything to do with it. I could not find any info to support this idea, but my mind is wandering....
  5. M

    So here's a new one...

    Thanks for the reply. I can leave my temp settings untouched. When I stop at a light it will blow HOT. When I take off it loses it's heat. My blend door actuator was also replaced last year when I originally chased this issue. The door was verified to be in working order when I replaced the...
  6. M

    So here's a new one...

    Long story short... My heat only works when the vehicle is stopped. It's very toasty. When cruising I only have "warm" air. It's a '99 XLT 4.6 Windsor I just did a coolant flush this weekend, distilled water ONLY. New thermostat and reservioir cap. Coolant level correct, air has been bled...
  7. M

    New Owner and need help

    FWIW I have a brand new DPFE sensor from AutoZone ( duralast ) that I tried to solve the P0401 with. Ended up having blocked EGR ports on my intake. If the coils, cops, and plugs have been changed, I suppose I'd go with fuel filter and air filters. They're cheap enough and probably need changed...
  8. M

    Looking for hard to find part.

    The pocket came with Velcro, attach one piece to the pocket and one to your opener. I have found that a BIC (crystal) pen cap fits nicely over one of those post slots. I just cut the long tab off the cap and it fits nicely.
  9. M

    What did you do to your expedition today?

    Cleaned my EGR ports from the TB-to intake manifold elbow. They were full of goop. Also found a loose exhaust clamp that had been rattling under there for a little while.
  10. M

    Engine Temp / Heat

    Sounds like it could be your water pump to me.... Check this thread out. My inlet hose was hot as hell, but my outlet hose was only hot from the engine heat. I'd say if you can squeeze the outlet tight for more than 5-10 seconds with a hot engine, the coolant isn't flowing through it. Link...
  11. M

    1998 expedition laser red Eddie Bauer parting out

    How about the fender trim over the wheels to Fort Wayne, IN? It appears to be all intact...
  12. M

    What the HECK is this on the back side of the center console?

    Ah-ha! Finally someone that agrees with me! I'm surprised no one commented on this, lol. Thats funny.
  13. M

    Suggestions for fender trim or flares... Rust coverup!

    Well, I appreciate your help. I think I'll try to fix it and cover it up with the chrome fender trim... I can experiment with the Plasti dip later...
  14. M

    Tranny to TC seal?

    I'm not certain... I just have tranny fluid that's leaking into the transfer case...
  15. M

    Anyone install a valve body (shift) kit in their Gen1?

    I don't have any real intentions of towing anything, as of yet anyways. Maybe a trailer sometime in the future... I'm more into looking to extend the life of my tranny.
  16. M

    Suggestions for fender trim or flares... Rust coverup!

    Did you clear coat the fender or did it have enough gloss?
  17. M

    Suggestions for fender trim or flares... Rust coverup!

    I will repair it, I just don't think I want to spend the money getting it painted...
  18. M

    Tranny to TC seal?

    I just changed my TC fluid a week ago and of course had one extra quart of fluid. Subsequently, my tranny was low one quart. Obviously, my seal between the two is worn. I can't really find any info on this repair, but for starters, does anyone know for sure if this is the front output shaft seal...
  19. M

    Anyone install a valve body (shift) kit in their Gen1?

    I searched unsuccessfully to see anyone has installed a valve body kit in their tranny? Mine shifts very smooth, like a caddy. I didn't think this was a bad thing, but my buddy said I should install a shift kit to extend the life of the tranny. It's just over 120,000 miles, so I'm going to be...
  20. M

    What the HECK is this on the back side of the center console?

    Thanks.
  21. M

    Suggestions for fender trim or flares... Rust coverup!

    I have just a tiny bit of body rust on my RH rear fender. I was thinking about the Putco stainless/chrome trim to cover it up. I am not a chrome whore, but my used truck came with a chrome gas door. I replaced the side moulding because it was waterlogged. I removed all paint from the 3...
  22. M

    What the HECK is this on the back side of the center console?

    I appreciate your attempt, Andy.
  23. M

    What the HECK is this on the back side of the center console?

    Hmmm... I think you're on to something. Until further notice this is what I'll use mine for. Great idea.
  24. M

    What the HECK is this on the back side of the center console?

    1999 XLT 4.6 Windsor 4WD
  25. M

    What the HECK is this on the back side of the center console?

    Yes, I have it but unfortunately it's not in there. I'm sticking with headphone hook for now, seeing as that rear console has a couple jacks.

Latest posts

Members online

Total: 1,491 (members: 31, guests: 1,460)

Forum statistics

Threads
53,615
Posts
502,496
Members
47,220
Latest member
dgwell521

Share this page

Top