Recent content by 05expedeb
-
0
blower wont shut off
Check under the drivers side floor to see if you have any water from possibly a leaky windshield. This is a common problem in the first gens Water leaks onto the fuse block/gem and causes those kind of problems. If you have water leaking onto the fuse block/gem you can try to use a hair dryer...- 05expedeb
- Post #2
- Forum: Heating & Cooling
-
0
Help! No power to OBD2, nor horn, nor starter...
Thanks for the update. That connector is C270a- 05expedeb
- Post #10
- Forum: 2nd Gen - 2003 - 2006
-
0
rear ac not blowing
When you get around to fixing the actuator you most likely will solve the problem.- 05expedeb
- Post #2
- Forum: Heating & Cooling
-
0
AC low side switch replaced, still no AC...
from the 99 service manual- 05expedeb
- Post #10
- Forum: Heating & Cooling
-
0
AC low side switch replaced, still no AC...
Hopefully stamp11127 will confirm those figures- 05expedeb
- Post #8
- Forum: Heating & Cooling
-
0
AC low side switch replaced, still no AC...
According to the wiring diagram the switch closes at 43.5 psi and opens at 23 psi- 05expedeb
- Post #7
- Forum: Heating & Cooling
-
0
AC low side switch replaced, still no AC...
Send a PM to stamp11127 as he is about the best to help you .- 05expedeb
- Post #4
- Forum: Heating & Cooling
-
0
AC low side switch replaced, still no AC...
When you replaced the switch you hand to open the system that would allow freon to escape. You would have heard that. If you didn't have any pressure in that line then you had no freon in the line.- 05expedeb
- Post #2
- Forum: Heating & Cooling
-
0
spark plug and coil on plug questions 03
In reading this thread may I suggest that you change the spark plug boot and coil wire inside of the boot. My opinion is that the boot may fail rather then the coil. AGAIN THAT IS MY OPINION. Also use dielect greese on the coil wire inside of the boot. If you do change the coils they...- 05expedeb
- Post #6
- Forum: Transmission & Drive train
-
0
Something keeps blowing my rear wiper fuse.
The reason the fuse blows is because it is drawing to many amps. This is called an OVERLOAD. putting in a higher rated fuse only allows the device to draw more amps. This results in even a larger OVERLOAD and allows more current into wires that aren't designed to handle the excessive amps. THE...- 05expedeb
- Post #2
- Forum: 1st Gen - 1997 - 2002
-
0
Help! No power to OBD2, nor horn, nor starter...
Recheck fuse 26 and 41and 101- 05expedeb
- Post #5
- Forum: 2nd Gen - 2003 - 2006
-
0
Walk away or should I pay?
Again money talks BS walks If you want it that bad then go with cash in hand and pull it out and tell him you are ready if he is. Then tell him that if not and he calls you back the offer will be $2000 But from what you say about the condition I wouldn't go over 2500 there are too many other...- 05expedeb
- Post #6
- Forum: General Discussion
-
0
New member in Va.
Shame you got it with the 4.6 for towing. Just my opinion- 05expedeb
- Post #4
- Forum: New Member Check-In
-
0
Walk away or should I pay?
Just my opinion but its way over priced Do a search on Craigslist for your area and other cities close to you to get a better idea of what is available and prices. Check KBB and NADA for values. Ask the seller how long he has had it for sale? From the pictures it does look nice and the milage is...- 05expedeb
- Post #3
- Forum: General Discussion
-
0
wheel hub assembly bkew apart
Expensive way to try and save on fuel expenses. You may have been better off to remove the front drive shaft- 05expedeb
- Post #4
- Forum: Suspension
