Recent content by retrogarage6
-
A/C whistling when button is pressed...
does the whistling sound sound like an air sucking whistle?? or a rubbing, metal plastic abrasive whistle?? That will determine if it's the motor or not.. if it' s an air sucking whistle then it's probably something else in the box, maybe even blocked. Since the start of AC season where I work...- retrogarage6
- Post #11
- Forum: 2nd Gen - 2003 - 2006
-
From A red ruby to "SINISTER" the rebirth of my 207,000 mile Expy.
So thats like $40 after tax for the rust-eeze, what else did you buy?? primer and all the fixins? new sprayer included in your spending? I would have to use my bros garage since the thing wont fit in mine lolll- retrogarage6
- Post #10
- Forum: 2nd Gen - 2003 - 2006
-
From A red ruby to "SINISTER" the rebirth of my 207,000 mile Expy.
dude... that is badass i really like it. How much did you have to use and how much about did you spend on this project? I'm a plasti dip guy and I'm impressed that is very nice! don't be mad If I copy you.- retrogarage6
- Post #8
- Forum: 2nd Gen - 2003 - 2006
-
hot/cold blender tips
i see... ok thanks for the info. It works right now but i don't want to wait until it gets stuck on either cold or hot in the wrong season.- retrogarage6
- Post #6
- Forum: 2nd Gen - 2003 - 2006
-
hot/cold blender tips
HM. That sucks. I attempted to remove the console when i ran wires for a future amp in the rear when i did my head unit. So i got the under the coin tray screws, there's a couple screws in the back of the console i remvoed, and theres gotta be some i missed because it wouldnt budge so I gave...- retrogarage6
- Post #4
- Forum: 2nd Gen - 2003 - 2006
-
Gotts Mod **Pics**
see whats i mean? click that and zoom in a bit. Notice the wetness inside the tube and gummy mess on the sensor. Lots of arguing about this.... the people that know they suck just dont use them, and the people that spent $50+ on filters or cold air setups just get mad that someone said theyre...- retrogarage6
- Post #22
- Forum: 2nd Gen - 2003 - 2006
-
Gotts Mod **Pics**
NOW don't get me wrong... I used to love K&N filters, oiled filters... makes a big difference. But have you ever noticed that the oil in those filters is getting sucked into the intake tube and coating the MAF with filter oil? Well it is. And just a matter of miles does the MAF fail and send...- retrogarage6
- Post #21
- Forum: 2nd Gen - 2003 - 2006
-
No start
yea, that sounds fun haha... wouldn't it be so much nicer to just remove the relay and plug in a nice little new one?- retrogarage6
- Post #17
- Forum: 2nd Gen - 2003 - 2006
-
A little help please? loud humming
Check your wheel bearings too... jack the truck up and see if the wheel moves when you push against it. Play in the wheel bearing can cause your wheel to fall of while driving so check that asap! hum is very typical of that also, I think i have the intermittent IWE hum going on so I'm checking...- retrogarage6
- Post #23
- Forum: 2nd Gen - 2003 - 2006
-
Front Sagging 04 Expedition
do you have air suspension? If you can't ID the shocks by looking at them open the access panel on the left of the luggage compartment in the rear and see if you have an "Air suspension off" rocker switch. If you only see the red button thats the fuel pump cut off and there will be the air ride...- retrogarage6
- Post #2
- Forum: 2nd Gen - 2003 - 2006
-
hot/cold blender tips
Hi all. Some HVAC things need advice on. 2003 XLT 5.4 with manual climate control and rear ac. The blender for hot/cold clicks repeatedly when trying to rotate left to tghe coldest setting, so I know the blender is getting stuck or needs to be replaced. I'm used to German cars, and...- retrogarage6
- Thread
- Replies: 5
- Forum: 2nd Gen - 2003 - 2006
-
No start
I'm sorry but soldering relays to the fusebox is junk ford... thanks! a $40 relay becomes a $200 fuse box.- retrogarage6
- Post #15
- Forum: 2nd Gen - 2003 - 2006
-
Play in the drivers seat track
so better off just finding a new seat track assembly used if it were myself, at least. Soudn like a real PITA fabricating and all that, theres plenty of crashed and block-seized expys out there haha- retrogarage6
- Post #7
- Forum: 2nd Gen - 2003 - 2006
-
Color codes/trim colors
that link doesnt work, but i'm interested also to check my vin there if you have a working link?- retrogarage6
- Post #3
- Forum: 2nd Gen - 2003 - 2006
-
Need help figuring out a part #
if you put your vin# in the fordparts.com site, it should give you a list of parts filtered for your vehicle. Just watch foot notes on parts that have any multiple choices or options such as color or trim level but generally thats why the vin# is entered. Close enough to the electronic parts...- retrogarage6
- Post #2
- Forum: 2nd Gen - 2003 - 2006
