Search results
-
Does anyone else hate Ford seatbelts?
It's wearing the finish off the side of the seat where it gets pulled through every time.- Miekk
- Post #4
- Forum: 3rd Gen Ford Expedition Interior
-
Does anyone else hate Ford seatbelts?
My chevy and dodge both have the belt buckle at about the left shoulder height where I can reach up with either my left or right hand and pull it easily down across to plug it in. Stupid expy and mustang buckles lay at the bottom so you can't get it with either hand without twisting and...- Miekk
- Thread
- Replies: 22
- Forum: 3rd Gen Ford Expedition Interior
-
Tired of washing sand out of your bumper at the car wash?
Same problem behind the handle and and the chrome piece on the rear gate. Need to remove and put foam tape behind them to stop that too...- Miekk
- Post #3
- Forum: 3rd Gen Ford Expedition Exterior
-
Tired of washing sand out of your bumper at the car wash?
I don't know why Ford left these nice big holes in the inner fender well. All the sand and crap gets thrown up there and then when you wash the bumper at the seam, all the crap keeps flushing out. Made these today.- Miekk
- Thread
- Replies: 2
- Forum: 3rd Gen Ford Expedition Exterior
-
Power running board broken arm casting.
All fixt. I does pay to know people....- Miekk
- Post #10
- Forum: 3rd Gen Ford Expedition Exterior
-
Painted grille today!
I see the 5-lug conversion on the fox, but what did you paint blue on the rotor?- Miekk
- Post #5
- Forum: 1st Gen Ford Expedition Exterior
-
Air Suspension
Love the air rear on my '08 and hope it doesn't cost an arm and a leg to keep...- Miekk
- Post #5
- Forum: 1st Gen Ford Expedition Suspension
-
Power running board broken arm casting.
Plan A: Remove and have friends shop remake from billet. Plan B: Model in ProE and have friends shop program CNC. Plan C: (probably most likely) 3x5 1/4" flat with single long tube welded to the bottom and two shorter with a gap for the wedge on the top. Weld a short wall on the top for the...- Miekk
- Post #9
- Forum: 3rd Gen Ford Expedition Exterior
-
Power running board broken arm casting.
I could just drill a hole through the bracket and the stop, but a bolt in it and I have really expensive rocker panels that constantly get full of crap under there.. I have a fairly local dealer that I've never found anyone beat for price, but $600 is still too much...- Miekk
- Post #8
- Forum: 3rd Gen Ford Expedition Exterior
-
Power running board broken arm casting.
Pieces:- Miekk
- Post #2
- Forum: 3rd Gen Ford Expedition Exterior
-
Power running board broken arm casting.
The power board deployed about half way down and when it got stepped on I heard a sharp snap. It went up and down a few times then wouldn't stay up. It's on the passenger side. I drove it up on the ramps and started looking. It turns out that the main drive arm casting that has the wedge block...- Miekk
- Thread
- Replies: 17
- Forum: 3rd Gen Ford Expedition Exterior
-
2V or 3V
http://www.minnesotacars.com/Ad/For-Sale.cfm/508454968/2007-Ford-Expedition/Redwood-Falls-MN/ OR- Miekk
- Post #29
- Forum: 2nd Gen Ford Expedition Engine & Performance
-
-
2V or 3V
If I want to wipe the floor, I'll just run the cobra. But a 650rwhp expy would be a nice sleeper.- Miekk
- Post #22
- Forum: 2nd Gen Ford Expedition Engine & Performance
-
2V or 3V
When I have any issues with my 08, I already it's replacement lined up out of a GT500... :happy107: 6K lbs sould be less of an issue with that...- Miekk
- Post #18
- Forum: 2nd Gen Ford Expedition Engine & Performance
-
2V or 3V
The 3V plugs breaking is not an issue with the tool. The plugs blowing out however is a little more difficult...- Miekk
- Post #3
- Forum: 2nd Gen Ford Expedition Engine & Performance
-
How do I stop the seat from moving all the way back when I remove the key?
How do I stop the seat from moving all the way back when I remove the key? I can't find it in the manual or interweb. It's anoying, unnecessary, and prematurely wearing out stuff?- Miekk
- Thread
- Replies: 1
- Forum: 3rd Gen Ford Expedition Interior
-
Spark Plug/Coils
Just replaced all the plugs today. Cracked them last night and let them soak till this morning. The first 3 I did the proceedure as stated by ford. All three broke. Then I stopped the "back and forth" part of the proceedure and just turned them out, not one more broke. Might be something there...- Miekk
- Post #10
- Forum: 3rd Gen Ford Expedition Engine & Performance
-
Finally painted the headlights
Just out of curiosity, who would buy a pair of non-OEM ones for $650 LINK when thier $202 new from Ford?- Miekk
- Post #18
- Forum: 3rd Gen Ford Expedition Exterior
-
IRS gurus help me out!
I have over 100k and no issues, I would take it back to the dealer. I don't know of anyone with these issues...- Miekk
- Post #11
- Forum: 3rd Gen Ford Expedition Suspension
-
Finally painted the headlights
Did you sand off all the chrome first? Are the remaining chrome beam projectors removable? How about thereflector? What paint? Gloss? Adhesion promoter? Is this similar or exactly like the limiteds have? If not, what's different? I'm nervous about wrecking my only pair of headlights. If I screw...- Miekk
- Post #15
- Forum: 3rd Gen Ford Expedition Exterior
-
-
Oil
Mustangs drain the filter directly over all the rack fittings and lines so for that, it's about the only way...- Miekk
- Post #9
- Forum: 3rd Gen Ford Expedition General Discussion
-
-
Paint code help
Thanks for all your hard work!- Miekk
- Post #8
- Forum: 3rd Gen Ford Expedition Exterior
