I need to replace the rear differential arm assembly for my 2016 Expedition EL XLT 4x4 and finding two different part numbers :8L1Z-4612-A and FL1Z-4612-A. The date code for my Expy is 4/16. Can anyone help with this. I am thinking the FL1Z is a replacement for 8L1Z but not sure.
TIA
Sent...
My boss’s son has some 2018 F150 STX wheels and tires that he took off his truck with very low miles and I need to know what I have to do about TPMS sensors so that I can use them on my 2010 Expy EL??? Can anyone help me wit my this, TIA!!!
Here are my current wheels:
Here is what I am...
All
I have a PO461 CEL code on my 2010 Expedition EL Limited that keeps returning after clear. It says that this is an indication of fuel level exceeds fuel capacity of the vehicle. I am not showing any variance in my fuel level as far as the gauge goes. Do I need to replace the pump/sending...
Update:
I went over it all and realized something I should have caught right away!!! They gave me a pass side caliper and the bleeder screw was on the bottom!!! I am embarrassed I made such a silly mistake [emoji85]!!! I got the correct part on ,bled the brakes and now have a good pedal...
I had a driver's side caliper hanging up so I changed rotors on both sides,new pads,new drivers caliper,and new front brake hoses. I gravity bled the front drivers caliper then went through the system twice starting in RR and moving farthest from driver to closest. When the vehicle is off it's a...
I thought I would post some info pertaining to the lower radiator hose on our vehicles since I couldn't find much before and I recently changed mine. The radiator side of the hose on my 2010 contains a spring clip with an alignment notch/tab and the engine side contains a normal spring clamp. To...
I finally got around to installing some new struts on my 2010 Expy. After lots of feedback (Thank you all)and internet browsing I decided to go with Bilstein struts. I installed them last Saturday. Everything went smoothly as far as installation goes. I removed the brakes, upper and lower ball...
Greg S I took some measurements of my front and rear wheel wells from top of the tire to underside of the well and from the ground to the bottom of the well and I only have 1/8" difference in height from front to back. My fear of going to Ranchos would be taking the front higher than the rear ...
Ztruke thanks for the recommendation. I know the feeling ,my struts are clunky and taking away from my better ride that I could have with replacement struts. I just need to make a decision already and order some
Sent from my Pixel using Tapatalk
Adieu do you have the Ranchos on your Expedition if so how do you like them and did you do the back at the same time because I don't want the front to be higher than the back.
Sent from my Pixel using Tapatalk
I have the mechanical ability either way assembled or bare because I used to be a tech, I am more just wondering what brand of struts people have had the best luck with. Both inner CV boots are torn too so I'll be doing axle shafts at the same time
Sent from my Pixel using Tapatalk
I need a new set of front shocks for my 2010 Expedition El 4x4 and looking for recommendations. I am most likely going to buy some off rockauto and they offer Motorcraft bare struts, Moog loaded assemblies,or Monroe loaded assemblies. I am not looking for anymore than what that stock ride...
Montecarlo31 i believe the wheels are aluminum underneath the cladding are they not? I haven't pulled the wheels off of it yet to know for sure. I know that they wouldn't have as fancy of design as the cladding but thought maybe they would look nice wet sanded and polished or painted black or...
Flexpedition thanks for the post, I will hopefully find someone who has done this who has a picture. I would love platinum 6 spokes but since I just bought it I don't think the wife will go for that right now! Just looking at a cheaper alternative and either polish or paint what's underneath ...
Anyone on here attempt to remove the chrome cladding off of factory 20" Limited wheels. Mine are chewed up on the edge from the previous owner having wheel weights mounted on the outside instead of static balancing. I was thinking of removing the cladding and painting/polishing the wheels. I...
ManUpOrShutUp ok so i am not missing a cover then. I don't really like that change because if you put the divider up and put stuff underneath it , it allows for another dirt trap or hearing whatever you have in the storage bin rattle.
ManUpOrShutUp I was referring to this area under the divider. My 08 had a cover over it when you put the divider up, did they change this in the newer models? If you can please take a picture of yours so I can compare.
ManUpOrShutUp
Thanks for the pic ,I was actually referring to the one under the divider tray,if you could lift it up and show me what it looks like that would be awesome.
Hey all I just bought another Expy EL today after a short stint of trying a 7.3 Excursion. I got a 2010 Limited 4x4 with 104,xxx miles. I won't be the Excursion down one bit cause I love the 7.3 but it is meant for a certain person who needs it and I missed my previous Expy EL and didn't really...
1955moose thanks for the response , I can agree with you on doing it the right way the first time. I currently have 139,xxx miles on it so it's probably just best that I do it all now and hope that it lasts another 100,000.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.