Thanks guys. I thought I'd read something about the dummy light coming on after deleting the rear cats but it's been a bit so I wasn't sure. No emissions tests thankfully as I'm in Ohio. Moose, as far as I can tell there isn't any exhaust leaks , I'm going to climb under and take a look. It's...
So, I love my Expy but the wife is starting to get frustrated with putting money into it. about a month ago we had the local shop cut all four cats off, weld up two new fronts and delete the two rears as well as change all four O2 sensors. It ran amazing and still seems to be but this morning...
Figured I'd post an update just in case others might think they can save a few bucks and get by doing an alignment themselves. Save your time and have a shop do it. Had it done professionally and the front end feels better than it did when we got it a few years ago. Thanks again @Hamfisted for...
So, I replaced the upper and lower ball joints, inner and outer tie rods and sway bar linkage on both sides about 7 months or so ago. Now it feels like every time I hit a bump or pothole my expy wants to drive itself off the road or into oncoming traffic. It also seems to want to drift left or...
I had asked a similar question a few years back. My problem tho was that the dvd in the overhead unit wouldn't eject but the Kenwood head unit i installed in the dash had dvd. I ended up running my own wires from the Kenwood and just hooked the rca's into the aux input on the overhead unit. My...
I kept the original hard line, just made my own boots or elbows or whatever their called. The hose I made the elbows with is thicker than what the factory had on it so should be just as good, if not better.
Instead of replacing the boots on the vacuum hose with boots, the only store that listed them close was out, I just bought some heater hose with elbows bent on the end. It ended up not being as tight a fit as it should've been so I put hose clamps on it.
I then followed this YouTube vid to...
Well I replaced the elbows and it's not wanting to die no but still idling rough while in gear. It's idling around 7k when in park and doesn't seem to go down any when in gear but almost seems like a miss and the exhaust smells horrible. Gonna borrow a friends code reader later today and see...
I smoked it and the elbows on the line running from the passenger side valve cover are shot also. Hopefully I can get my hands on a couple today. Thanks again for the info guys.
Hello all, my 03 4.6 has had a rough idle after warming up for months now, at first it was barely noticeable but all of a sudden it went from barely noticeable to the point of wanting to die at idle. A few days ago the CEL came on with P2195 and P2197. It's fine for about 3 minutes after the...
Hey everyone, just wondering if there is two different sizes of upper control arms on the 03 XLTs? I ordered a suspension kit and didn't measure the control arms. The listing said standard suspension 9 1/2" bushing to bushing. I got the stuff and the control arms are not wide enough. Everything...
Just wondering what plugs are recommended for the 03 4.6? I've searched and found motorcraft is the recommended brand but is copper or platinum better? Also, I was wondering how to test the cops, I couldn't seem to find anything about that.
Sorry, meant to say thanks wizard for the info and the link earlier. Looks pretty much the way I was thinking from watching the video. Minus the axle as mines only 2wd. I'll be blocking the beast up definitely. My dad stressed safety all growing up, he had a friend lose his like doing brakes...
Well, it's a wheel bearing. So much for something simple. Anything I should be aware of when changing it? Am I correct in thinking I just remove the caliper, bracket and the 4 bolts holding the bearing assembly on? No special tools required? Thanks again guys.
Also who else thinks the factory...
Thanks for the tips guys. I finally got a day off from work so I'm gonna pop the wheels off today and poke around. It seems to be doing it more and more frequently. I crawled under and looked at the tie rods and ball joints and they "look" ok but will inspect them more thoroughly when I get the...
Hello all. So, not sure how to describe this exactly. Every so often for a couple months now when pressing the brake pedal in I get a slight kinda click/not quite a clunk/sorta vibration for just a second when coming up to a stop. It doesn't seem to do it a coasting speed. There's not a wheel...
Anyone know what the empty hole plugs are called for stuff that didn't come equipped? I've got a hole in the bottom front of the center console under the armrest. Looks like maybe for a light. I was thinking about running my Kenwood's USB to it but I'd like to get a snap in hole plug and make it...
Thanks so much Flexpedition for the info and part numbers. Still sol so far but I sent my local dealers service department an email asking if they'd share any info on wiring. Wonder what the odds of them sharing are?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.