Dropped cam bolt

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Hhernandez91

Member
Joined
Jan 9, 2021
Posts
7
Reaction score
5
Location
Dallas tx
I was replacing the passenger side cam I managed to drop a cam cap. After finding it only one bolt was attached I was not able to locate the other one. I believe it may have fallen into the head and into the oil passage. Any advice on where to go from here would be appreciated.
 

Hamfisted

Full Access Members
Joined
Nov 20, 2012
Posts
2,902
Reaction score
1,822
Location
Ft Lauderdale
Run a magnet stick down the suspect oil passages. But it'd be hard for a cam cap bolt to pass into one of those dime size holes, you'd have to be really unlucky. Did you notice what the cap bounced off of on it's way down? I usually find that they hang up in the front suspension somewhere right under where they where mounted. There's a lot of heat shields and such that the bolt can go flying into, but I'm sure it's there somewhere. Were you working in the grass or something? Can you drag a magnet through the area? Can you see with a bright flashlight into the oil holes, maybe with a mirror to help. But if you run a magnet stick down each hole and come up with oil and no bolt don't be surprised. But that would be kind of good news I guess. Then just finding the bolt becomes the next issue. They do sell replacement bolts though, so don't panic. What year is your Expy ?

https://www.amazon.com/36-Flexible-...YQQ7HW6VVDZ&psc=1&refRID=V3X2D0ARTYQQ7HW6VVDZ


https://www.amazon.com/Ullman-HT-55...7FBDFN571PR&psc=1&refRID=GHXY5FCCA7FBDFN571PR


https://www.amazon.com/V8-Tools-382...G2SRN5F7831&psc=1&refRID=N8WC7G9KYG2SRN5F7831


Camshaft bearing cap bolt....
https://www.ebay.com/itm/Genuine-OEM-Ford-F6AZ-6L293-AA-Camshaft-Bearing-Cap-Bolt-/124072538938



1136a52a440d66c97252ac9f72e01cc3.jpg
 
Last edited:
As an eBay Associate we earn from qualifying purchases.
As an Amazon Associate we earn from qualifying purchases.
OP
OP
H

Hhernandez91

Member
Joined
Jan 9, 2021
Posts
7
Reaction score
5
Location
Dallas tx
It’s an 05 it’s sitting in the drive way not grass it could be in the suspension it so tight over on the passages side you can only get in there so much. The cap landed on the frame right next the exhaust manifold in the rear of the engine when I managed to fish it out there was only one bolt. I tried using a flashlight you can see in the oil passage sort off but you can see it’s not there at least not stuck right at opening. Thanks for the idea of the magnet will definitely try it. And was definitely panicking over finding a replacement.
 

Hamfisted

Full Access Members
Joined
Nov 20, 2012
Posts
2,902
Reaction score
1,822
Location
Ft Lauderdale
Yeah, a lot of folks take the inner wheel well liner out just to get to the valve cover bolts when they're doing this work. Might be worth it if you haven't done it already. Take the wheel off, and the liner and you'll have good access and visibility in that area. Did you already pop the heater hoses off from the front heater core? That helps too. They make a tool to help get the heater hose click fittings off the heater core, makes it pretty easy. ( 5/8" fork tool....) Other than that you can fiddle with it with your fingers, but that can be a struggle. Squeeze the white clips in and push in on the hose and pull it off. The clips will remain on the heater core, then you just spread them to pull them off the core's pipe and put them and their O-rings back together with the click on hose end.

https://www.amazon.com/Performance-Tool-W83108-Heater-Disconnect/dp/B001DKLKRS

https://www.amazon.com/OEMTOOLS-27106-Heater-Hose-Disconnect/dp/B004FEHZB4

FfsJyD.gif
 
Last edited:
As an Amazon Associate we earn from qualifying purchases.
OP
OP
H

Hhernandez91

Member
Joined
Jan 9, 2021
Posts
7
Reaction score
5
Location
Dallas tx
I did remove the wheel well still couldn’t find it I didn’t remove the hoses. Today was rain/snow day so I couldn’t go out there and keep looking. Ordering the magnet today so hopefully it gets here soon.
 

Hamfisted

Full Access Members
Joined
Nov 20, 2012
Posts
2,902
Reaction score
1,822
Location
Ft Lauderdale
Good news ! Are you replacing the stock oil pump with a high volume pump ? That was a Ford fix later on in the engine model. Get more oil to that passenger side cam area. Run 10w-30 synthetic oil too, not that 5w-20 cooking oil.
 

Aspen03

Full Access Members
Joined
Apr 24, 2019
Posts
727
Reaction score
361
Location
Indianapolis
One of the USB borehole cameras would be useful in the future for something like this. Could be a sound investment for future work. Its great when you lose something in a hard to determine/reach area. They're pretty cheap these days and work with most phones or tablets.
 

Members online

Forum statistics

Threads
57,466
Posts
539,066
Members
47,413
Latest member
xojgiiox
Top