Wrench light, no crank, no start, no communication

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Jason Hallq

New Member
Joined
Sep 12, 2019
Posts
2
Reaction score
4
Location
Virginia
2007 Expedition lost power couple miles from the house. Wrench light came on with no CEL. Got home, went to get scan tool and shut truck off. Now it will not turn over at all, and my scan tool won't even power on when plugged into the data port, so I can't even check for any codes. Battery is good. I checked fuses and all seem good. It was at night, so I may have missed something. Any ideas where to start? I really don't want to tow it anywhere.
 

mjp2

Full Access Members
Joined
Apr 19, 2017
Posts
486
Reaction score
308
Location
Howell, NJ
Did you test the battery at the posts or through the connectors? What voltage did you see?

It's worth pulling the terminals off the posts and cleaning up the contact surfaces in case you have some corrosion built up in there. It's a quick step that costs nothing.
 

99WhiteC5Coupe

Full Access Members
Joined
Jun 3, 2015
Posts
3,509
Reaction score
2,074
Location
USA
Did you test the battery at the posts or through the connectors? What voltage did you see?

It's worth pulling the terminals off the posts and cleaning up the contact surfaces in case you have some corrosion built up in there. It's a quick step that costs nothing.


Removing the connectors will erase any stored trouble codes. Perhaps the OP could ensure the connectors are tight and corrosion free without removing them?
 

mjp2

Full Access Members
Joined
Apr 19, 2017
Posts
486
Reaction score
308
Location
Howell, NJ
Removing the connectors will erase any stored trouble codes. Perhaps the OP could ensure the connectors are tight and corrosion free without removing them?
I tried that years ago with an old Bronco that wouldn't start. It had a relatively new battery (2 years old) but one evening I just couldn't get it to turn over. Ran just fine when I parked it a couple hours earlier. Tried jump-starting it with no success. Made sure the terminals were tight and everything looked clean. I was at a loss.

Then my dad came out with a wrench and a terminal & post cleaning wire brush tool. Popped off the connections, cleaned them up, put it back together, and the truck started right up. I learned that day.
 

99WhiteC5Coupe

Full Access Members
Joined
Jun 3, 2015
Posts
3,509
Reaction score
2,074
Location
USA
I tried that years ago with an old Bronco that wouldn't start. It had a relatively new battery (2 years old) but one evening I just couldn't get it to turn over. Ran just fine when I parked it a couple hours earlier. Tried jump-starting it with no success. Made sure the terminals were tight and everything looked clean. I was at a loss.

Then my dad came out with a wrench and a terminal & post cleaning wire brush tool. Popped off the connections, cleaned them up, put it back together, and the truck started right up. I learned that day.


As a matter of routine maintenance, I remove and clean the battery terminal connectors on my vehicles in the Fall.

I was unsure if the OP knew that he may erase any stored trouble codes by disconnecting the terminals.
 

mjp2

Full Access Members
Joined
Apr 19, 2017
Posts
486
Reaction score
308
Location
Howell, NJ
I immediately took your post as a "Noooes don't do it! You're gonna lose your data!" type of thing rather than something simply and very usefully informational.

The internet has ruined me :redface:
 
OP
OP
J

Jason Hallq

New Member
Joined
Sep 12, 2019
Posts
2
Reaction score
4
Location
Virginia
Sorry for delay in the update, but we are back in business.

Went back to the basics, starting with the battery, and checked good. Checked all fuses with test light in both compartments, and found the "transmission ignition" fuse blown. Replaced fuse and immediately popped again. Tada! Traced wiring to transmission and found where a clip had broken, and the wires had fell to close to the manifold and melted. Repaired wires and all is good!
 

mjp2

Full Access Members
Joined
Apr 19, 2017
Posts
486
Reaction score
308
Location
Howell, NJ
Sorry for delay in the update, but we are back in business.

Went back to the basics, starting with the battery, and checked good. Checked all fuses with test light in both compartments, and found the "transmission ignition" fuse blown. Replaced fuse and immediately popped again. Tada! Traced wiring to transmission and found where a clip had broken, and the wires had fell to close to the manifold and melted. Repaired wires and all is good!
Nice troubleshooting. Tracing a wire break is a PITA but gratifying as anything when it's found/fixed. Congrats on the fix!
 

Members online

Forum statistics

Threads
57,466
Posts
539,066
Members
47,413
Latest member
xojgiiox
Top