Recent content by chisan

  1. C

    2000 expy 5.4L eddie bauer 4x4 279k 02 sensor data, is it bad?

    With the engine on: long term trim (1) -21.9 Long term trim (2) -14.1 St trim (1) -7.0 St trim (2) -3.9 St trim (11) -5 5 St trim (21) -3.1
  2. C

    2000 expy 5.4L eddie bauer 4x4 279k 02 sensor data, is it bad?

    Those readings above are with the engine off, key on
  3. C

    2000 expy 5.4L eddie bauer 4x4 279k 02 sensor data, is it bad?

    Hi everyone, I am having rich condition with my expy, code is po175. I changed my fuel injectors and cop's. I used my scan tool to check the data form the truck and this is what I found. my question is does this mean my o2 sensors are bad? thank you.
  4. C

    does anyone know how ot repair or replace this?

    that option with cutting off the bottom of it sounds like a good idea!! Ill let you guys know how it go's. thank you very much
  5. C

    does anyone know how ot repair or replace this?

    that is the stop for the bump stopper on the lower control arm.
  6. C

    does anyone know how ot repair or replace this?

    Thanks Bob, I am hoping someone has a easier fix, lol. I dont know how to weld or what plate to use. I would have to find someone who is able to do that and know what kind of plate to use.
  7. C

    High mileage Expys?

    280k here 5.4L, 2000 eddie bauer expy
  8. C

    does anyone know how ot repair or replace this?

    this part of my 2000 eddie bauer expy 4wd 5.4L. has busted, and caused the boot on my upper control arm to tear apart. does anyone know how to repair or replace these since they are welded onto the frame? thanks.
  9. C

    Steering gear box removal 5.4 4x4

    I used a torch, pb blaster banging on it with my mini sledge. bent my pitman puller. tried to get the pitman arm off the drag link, but that was a pain and it didnt come off even tho i used a tie rod puller...it started to bend. I a leaving the pitman arm puller on and torqued really tight and...
  10. C

    Steering gear box removal 5.4 4x4

    Yea i didnt want to use the pickle fork because of the boot, but i did get my pitman arm puller on and i have be turning in until the hooks end start bending around the pitman arm. several shots of pb blaster and it still wont come loose but my puller is bending....smh
  11. C

    Steering gear box removal 5.4 4x4

    Can anyone tell me the best way to get the pitman arm off the drag link. Its a 2000 expy eddiebaur 4x4, 5.4L. I amcrammed for space, thought about a pickle for but dont want to destroy the boot. Icant remove the arm fromthe gear box because i have no room for the seperator. Thanks in advance.
  12. C

    exhaust manifold stud ideas

    Hey guys i got my passenger side exhaust manifold off my 00 expy 5.4 4wd i have gotten all the stud and both exhaust flange bolts off without a problem until now, i have 3 studs left in the cylinder head they are sticking out alittle more than 1/2 inch out of the head without the nut . i tried...
  13. C

    AC clutch harness no voltage

    how do i "draw down" a vacuum
  14. C

    AC clutch harness no voltage

    how do i know if my switch i bad? or should i just go ahead and replace it?
  15. C

    AC clutch harness no voltage

    ok thxs a lot guys i jumped the harness and the clutch kick in and started spinning.
See more

Latest posts

Members online

Total: 937 (members: 2, guests: 935)

Forum statistics

Threads
53,588
Posts
502,235
Members
47,171
Latest member
sharprd65

Share this page

Top