Recent content by jeremiahm
-
Rancho Quicklift
Plenty of space for lots more tire.- jeremiahm
- Post #33
- Forum: 2nd Gen - 2003 - 2006
-
Rancho Quicklift
I run 255/75/18 on stock 2011 F150 rims. Looks good diameter but narrow. Hancook DynaPro’s- jeremiahm
- Post #32
- Forum: 2nd Gen - 2003 - 2006
-
Rancho Quicklift
If I remember right the factory strut and rancho were identical except the lower part of the Rancho strut was lengthened some. Between the bottom of the chamber and the lower mounting hole. I think I have a side by side picture, will try to find. -jeremiah- jeremiahm
- Post #29
- Forum: 2nd Gen - 2003 - 2006
-
Rancho Quicklift
Hey joethefordguy, I believe the 5" of stroke on the strut translates to 9" of travel when you get out to the center of the wheel, so the travel stays the same. Thes struts give a bit of lift, so you can run a larger tire with less rub and they give you adjustability for your prefered firmness...- jeremiahm
- Post #27
- Forum: 2nd Gen - 2003 - 2006
-
03 4.6 L 2wd Front Lower Ball Joints stuck
When i did mine i found out there is a steel insert in the knuckle on the lowers. Too much heat and that came out with the ball joint still connected, took an oxy torch to heat it up enough to seperate. There is a pin through the knuckle to hold the insert in so i had to heat the knuckle again...- jeremiahm
- Post #5
- Forum: 2nd Gen - 2003 - 2006
-
lifted my truck
Looks great! I need to do spacers next...- jeremiahm
- Post #2
- Forum: 2nd Gen - 2003 - 2006
-
Small Y-pipe coolant leak
Thanks for the tip, getting this done soon!- jeremiahm
- Post #6
- Forum: 2nd Gen - 2003 - 2006
-
Is there something I am missing? (Front Suspension Clunking)
check the top nut on the struts (that holds the assembly together). I did all this work last summer and chased a stupid clunk for months. Finally discovered it was the top nuts. I had to pull them off (with car on ground) and put a thick washer to get the fully tight. Just the tiny bit of play...- jeremiahm
- Post #7
- Forum: 2nd Gen - 2003 - 2006
-
04 with Rize lift posted in Denver!!
It's like finding a unicorn... Just wanted to share! https://denver.craigslist.org/cto/d/lifted-ford-expeditionwill/6703905537.html -jeremiah- jeremiahm
- Thread
- Replies: 0
- Forum: 2nd Gen - 2003 - 2006
-
Rancho Quicklift
Put these on mine about 8 months ago and 7k miles. So far so good. The lift is nice. My only complaint is they are stiff on the small bumps. Our neighborhood roads have lots of imperfections and i feel them all, on the freeway it handles great and does well on the rutted dirt roads. Getting the...- jeremiahm
- Post #25
- Forum: 2nd Gen - 2003 - 2006
-
Steering wheel vibrates when you hit a bump
Hey pkuchirka, Put the quick struts on mine as well about 20k ago and think i had the same issue. Try tightening the nuts on top of the struts (that hold the assembly together). Mine needed washers so i could get them tight enough, no more rattle after that! Jeremaih- jeremiahm
- Post #12
- Forum: 2nd Gen - 2003 - 2006
-
05 XLT front axle leak
I have been looking at this on my 05 as well. May want to check the bearings inside the housing. I can grab where the axle at that end and move it a bunch. I have read some other posts about rebuilding the whole center section due to the bearings going out. Just a thought. Jeremiah- jeremiahm
- Post #4
- Forum: 2nd Gen - 2003 - 2006
-
2nd gen on 37s (pic dump)
How did you get the rear end up that high? body lift too?- jeremiahm
- Post #6
- Forum: 2nd Gen - 2003 - 2006
-
-
New shoes from and F150
I just set them as links, will find a way to post pics some day. Jeremiah- jeremiahm
- Post #10
- Forum: 2nd Gen - 2003 - 2006
Staff online
-
GriffinAdministrator -
Mediamonkey11Super Moderator