Recent content by SG1NUT
-
S
2004 Ford Expedition for sale
Yes, exactly. I believe the console is out of an ambulance chassis, resold after being taken out in lieu of a console built for lights/siren controls. Unfortunately, I don't have the tow mirrors anymore. They didn't work out very well, and were actually very poor quality. They vibrated so... -
S
2004 Ford Expedition for sale
Grille guard was made by Sterling Equipment out of Florida. They custom make them to your specifications, and I have been very happy with mine. And the center console is actually out of a Super Duty, since my truck didn't come with one when I bought it. -
S
2004 Ford Expedition for sale
2004 Ford Expedition - $6500 Call or text 269-547-8461 with questions, or use e-mail. I check my e-mail very regularly. No trades - Offers will be considered - 5.4L V8 - 130xxx miles (will increase slightly, as I will still be driving the truck) - Four wheel drive (4WD) - Automatic 4WD option... -
S
Got my truck painted
Yes, the push bumper is for the 2004 model year. I believe that any push bumper from 2003-2006 should fit though.- SG1NUT
- Post #33
- Forum: Member Photos
-
S
Got my truck painted
Yes, the push bumper does move around a bit. Not enough to create an issue though. As for the black wheels, I have been thought about painting the original steel wheels black. I will have to reconsider it now. :)- SG1NUT
- Post #31
- Forum: Member Photos
-
S
Got my truck painted
I can't quite remember what you mean by that. I drilled throught the top of the reverse housing straight down, and dropped the bulb down through the hole.- SG1NUT
- Post #24
- Forum: Member Photos
-
S
Got my truck painted
For the reverse lights: At first, I welded some cheap driving lights to the hitch receiver. But I wasn't very happy with that route, and I drilled some holes in the reverse light housing. I put the halogen bulbs in the holes. It works pretty well.- SG1NUT
- Post #22
- Forum: Member Photos
-
S
Got my truck painted
To start, I rewired the brake lights to all get power from the CHMSL circuit, so they no longer flash as turn signals. Then, I ran wires from the front, sending power directly to the turn signals in the back. That way, they only act as turn signals and not brake lights. I used the...- SG1NUT
- Post #20
- Forum: Member Photos
-
S
Got my truck painted
2. Around 20 minutes, give or take. 3. The mirrors I have now are the OEM mirrors that came on my truck.- SG1NUT
- Post #16
- Forum: Member Photos
-
S
Got my truck painted
2. I cut until the base fit. 3. My mirrors now are heated, but do not have the turn signal.- SG1NUT
- Post #14
- Forum: Member Photos
-
S
Got my truck painted
1. The cross bars were not on the truck when I bought it; I assume they were removed by the police department. 2. I used a dremel with the mini drum sander attachment to enlarge the holes on the taillights. 3. I have the OEM mirrors back on, although I painted the glamor cap gloss black to...- SG1NUT
- Post #12
- Forum: Member Photos
-
S
Instrument Cluster Swap
I have a 2004 Expedition without the message center. It has the boring, plain instrument cluster, and I want to swap in a newer cluster out of a 2006. I have a few questions about that. If it has the message center (Which I am not sure that it does), will I still be able to see my...- SG1NUT
- Thread
- Replies: 1
- Forum: General Discussion
-
S
My 3rd mod: Landing lights
Yes, I have installed strobes into several different vehicles. Personally, I prefer to run the cables underneath the step plates inside the vehicle. I've run plenty of wiring in my Expy, and there should be enough space for several cables. I would not run the cables under the vehicle, because...- SG1NUT
- Post #12
- Forum: Member Photos
