Recent content by Spooky
-
Gibson 619999 Stainless Steel Exhaust NIB (2004 Expy)
I have a Gibson 619999 Stainless Steel Exhaust NIB. Bought it years ago and never installed it (or opened the box). Since I've upgraded to a '22 Raptor, I don't need it. Asking $400, buyer pays shipping. Located in 20165. GIBSON Fits 2004 Expy. Tubing Diameter: 2.50-in. Stainless mandrel bent... -
2015 Ford Expedition wheels
I just put 2015 F150 wheels onto my Expy and had to use an angle grinder to cut about an inch off of the axle like Buck did. It was easy and took all of 20 minutes for both sides..... -
How do I fix this??
That could be a great resource if it works. I had the rear defrost tab pop off on my old Crown Vic and I couldn't find a product that worked. The only other option was to replace the rear window.....needless to say, that tab dangled for a while....- Spooky
- Post #4
- Forum: 2nd Gen - 2003 - 2006
-
Scored some F150 wheels
I think anytime you lift the Expedition, especially the 2/3 lifts, it alters the geometry of the rear axle a bit. The picture accentuates it. It doesn't look as bad in person....- Spooky
- Post #5
- Forum: 2nd Gen - 2003 - 2006
-
Scored some F150 wheels
I purchased a milwaukee 4.5" grinder and took off about 1/2" of the axle nub from each of the rear axles. The grinder made short work of them and I was able to get the cut portion of the axle flat so it doesn't look like chit. Before: IMG_2252 by Spooky posted May 23, 2017 at 4:12 PM After...- Spooky
- Post #3
- Forum: 2nd Gen - 2003 - 2006
-
Scored some F150 wheels
After much deliberation and searching, I found some cherry 18" wheels off of a 2015 F150 that I love ($350 shipped). I going to get them mounted and some new tires slapped on them as soon as I figure out how I am going to trim the rear CV axle to fit the F150 FORD wheel cap. Any ideas how I...- Spooky
- Thread
- Replies: 4
- Forum: 2nd Gen - 2003 - 2006
-
AP Racing 6 piston front brake kit 2003-06
Shoot me pics. I'm very interested...... -
AP Racing 6 piston front brake kit 2003-06
Is this kit still available? -
2006 Expedition - HID Headlights with Angel Eyes?
I had smoked headlights on my other car. The cut the visible light by almost half. I'll never do that again......- Spooky
- Post #11
- Forum: 2nd Gen - 2003 - 2006
-
2006 Expedition front blend door motor
YH-1744 was the correct p/n for the front blend door actuator for my 2004 Expy.- Spooky
- Post #10
- Forum: How To Section
-
2006 Expedition - HID Headlights with Angel Eyes?
I purchased the Spyder Angel Eyes housings recently due to the fact that my HIDs had way too much light spill and were probably blinding people. They are good quality and have so far preformed great. Spyder states that they will not accept HID bulbs, but my 9007 HID bulbs fit fine. The...- Spooky
- Post #8
- Forum: 2nd Gen - 2003 - 2006
-
2004 Expy having weird A/C issue
FYI, YH-1744 was the correct p/n for the front blend door. Hopefully this will fix the issue- Spooky
- Post #2
- Forum: Heating & Cooling
-
2004 Expy having weird A/C issue
So basically, even when I have the A/C or heat off, I still get a bit of either hot or cold air through my vents depending on how I have the temp set. Not a lot, mind you, but enough to notice. I figure it's the front blend door. Has anyone had this issue? Is YH-1767 the correct part number...- Spooky
- Thread
- Replies: 1
- Forum: Heating & Cooling
-
2006 Expedition front blend door motor
Sorry to bring this back to life, but does anyone have a part number for the front blend door actuator? I found YH-1767, but wanted to confirm as I need to change it this weekend.- Spooky
- Post #8
- Forum: How To Section
-
2nd Gen Expy.....what size tire increase?
Hey guys, I'm looking to get a set of 2014 Raptor SVT wheels with 315/70/17 tires and I was wondering if they will even fit? I'm currently running a 2.5" front and 1" rear level/lift. It LOOKS like they will fit, but I don't want any rubbing issues. Does anyone currently run a similar set up...- Spooky
- Thread
- Replies: 1
- Forum: Suspension
