Recent content by SkyJumper
-
99 expy main beams
Sounds like to me you have a closed circuit path for the low beams, or a bad light switch.- SkyJumper
- Post #3
- Forum: 1st Gen - 1997 - 2002
-
-
Tires
Looks like your springs are sagging in the rear.- SkyJumper
- Post #2
- Forum: 1st Gen - 1997 - 2002
-
-
New 2 me 1999 Ex 4x4
Hey guys, I am on vacation right now in Puerto Rico until the first of July, been 3 weeks already. I am ready to come home for sure. Since I am on here right now, I have a question. Before I left for vacation, I noticed I have a oil leak coming from the P/S upper back area of the engine that...- SkyJumper
- Post #141
- Forum: 1st Gen - 1997 - 2002
-
Edge Products
And just think, I just paid full price last month. :bawl:- SkyJumper
- Post #3
- Forum: General Discussion
-
Expy Overhaul
I would not go that route as I would bet that has nothing to do with the vibration. I would be looking at a possible out of balance tire/ I usually have my tires road forced balanced and that usually is right on to the tee. Road force balancing is the only way to go with truck tires. Or...- SkyJumper
- Post #55
- Forum: 1st Gen - 1997 - 2002
-
If you are running Goodyear Silent Armor tires (MUST READ)
National Highway Transportation Safety Administration’s (NHTSA) Office of Defect Investigation (ODI) announces new Recalls & Alerts: Goodyear Tire Recall 40,000 defective Goodyear tires have been recalled for their propensity to experience a tread separation while the vehicle is in...- SkyJumper
- Thread
- Replies: 2
- Forum: General Discussion
-
New 2 me 1999 Ex 4x4
Well the CV axle Gremlin bit me again over the past week. I had to go out and get a new axle for the P/S this time. That makes a total of 3 shaft replacements in the past 3 months due to this TT lift. And keep in mind that I only lifted the front by 1.25" instead of full twist. The boots are at...- SkyJumper
- Post #140
- Forum: 1st Gen - 1997 - 2002
-
Can anyone identify these 17 inch rims?
I agree with Dib52, I have polished up aluminum rims many of times in the past. it is alot of elbow grease involved as a drill and cone applicator and or polisher can get only so much of the open area's and spoke ports. Then it requires your elbow grease to do the rest. Mothers in my opinion is...- SkyJumper
- Post #13
- Forum: 1st Gen - 1997 - 2002
-
Can anyone identify these 17 inch rims?
They are American Racing Brand, The name of them are American Racing 1605873 - American Racing Polished Atlas Wheels Here is a link to them in polished aluminum...- SkyJumper
- Post #8
- Forum: 1st Gen - 1997 - 2002
-
Opinions on repair bill...
Well even at the Stealerships here, the rate is right at $65.00 and most of that goes to the Stealership and the tech gets half for the most part or is at a company hourly rate. And most stealership mechanics that I have ever met are book conscience and diagnostically dumb. Meaning as a...- SkyJumper
- Post #5
- Forum: General Discussion
-
What's your GAS price in your town?
I am running 87 octane with the 87 octane tune. I filled up this past Saturday and it was $103.45 at $3.96 a gal.- SkyJumper
- Post #35
- Forum: General Discussion
-
Opinions on repair bill...
Well that seems ridiculously high. The going labor rate here is $45.00-$50.00 a hour. So at 6 hrs and $50.00 a hr, that comes to $300.00 in labor. So with that said, the parts are going to cost an additional $625.00 to come out to $925.00. Something does not add up.- SkyJumper
- Post #2
- Forum: General Discussion
-
Sct
Only using a tuner with a CAI and Exhaust, I find that kinda hard to believe. Especially when you state improved 100% over stock.- SkyJumper
- Post #13
- Forum: After Market Add-Ons
