Search results
-
What do you pay for an oil change?
I usually pay around $60 US.... at the dealer. 2003 Expedition....- Andrew-XLT-Ford
- Post #30
- Forum: 3rd Gen - 2007 - 2017
-
-
Where are you from?
I am from Springfield Mass... Selling my 2003 Expedition, but don't have enough post ( more than 50 ) in order to post this in the for sale section. Can any one help... i have a link to all info that plays on Youtube... Thanks for the help.... Andrew- Andrew-XLT-Ford
- Post #578
- Forum: New Member Check-In
-
Engine stall at speed- no code
I have been having same issues that all started 2 weeks after my tranny rebuild. (May-2019) found my Negative battery terminal loose. but pulled the fuse panel to check, and the relay was fried, with a hole in the side. So far, i replaced my fuel filter, the relay, then the fuel pump... 3 weeks...- Andrew-XLT-Ford
- Post #16
- Forum: 2nd Gen - 2003 - 2006
-
Misfire or something else??
Overdrive clunk; Engine loss of power while driving; Hesitation/skip upon takeoff; Rear end grinding while turning at slow speed Multiple Updated parts: My 03 Expedition XLT had a problem grinding while turning corners.. So i had a new diff installed.. A Torsen Diff , that has no clutch...- Andrew-XLT-Ford
- Post #44
- Forum: 2nd Gen - 2003 - 2006
-
F150 Platinum Wheels on Expedition - extra spindel
Just an Idea, Maybe use a wheel offset Spacer for the Rear... It would push out the Rear wheels just enough to clear the caps, and also make the back "stance" wider... only by a 1/2" per side... or whatever size you buy. I am thinking of putting 315/70 R17 Tires on my Stock 17 wheels... I am...- Andrew-XLT-Ford
- Post #11
- Forum: Exterior
-
2003 XLT where to find the Code for the "keyless door pad"
This worked out well for Me, So I owe you a Thank You!!! Note to all, Before attempting to reach up into this small space with you upper body in a very dangerous Twist... Either Stretch first,... or get someone with a short/small build to do this... My good buddy found this code for me... It...- Andrew-XLT-Ford
- Post #4
- Forum: 2nd Gen - 2003 - 2006
-
M12 or M14 lugs
2003-2006 uses M14 x 2 Lugs/Nuts... I just bought my rims recently and needed wheel lugs, so I ordered Lugs from amazon... Note that these are 6 Lugs/Nuts per wheel... so 24 in total... Rim/Wheel Bolt pattern= 6 x 135mm- Andrew-XLT-Ford
- Post #2
- Forum: 2nd Gen - 2003 - 2006
-
2003 XLT where to find the Code for the "keyless door pad"
Thank you, I will check this out tomorrow... Will Verify when I find it....- Andrew-XLT-Ford
- Post #3
- Forum: 2nd Gen - 2003 - 2006
-
2003 XLT where to find the Code for the "keyless door pad"
Need help to locate where the keypad module is.... I think that the code should be on a label on that unit... Dealer wants$50. This is a DIY project. I can take apart panels....no problem, just want to know where to access this. Thankyou- Andrew-XLT-Ford
- Thread
- Replies: 5
- Forum: 2nd Gen - 2003 - 2006
Latest posts
-
-
-
Odd vibration/rattle from engine (?) on incline in higher gear
- Latest: eddytheexpy
-
-
Staff online
-
GriffinAdministrator