Search results

  1. BrinkExpo

    Cylinder 1 Misfire. NOT plug,coil,or injector. Help

    Right, so do you think it is more likely an injector or valve springs? Just wondering what to do next?
  2. BrinkExpo

    Cylinder 1 Misfire. NOT plug,coil,or injector. Help

    He said compression was good
  3. BrinkExpo

    Cylinder 1 Misfire. NOT plug,coil,or injector. Help

    Hey guys I am getting a misfire on cylinder 1 on my 06 expo with 160k miles. The local Ford service manager and I went for a drive with his computer hooked up to find that it was cylinder 1 because it was not throwing a code. It only does it around 3,000RPMS and up. We tried swapping coils and...
  4. BrinkExpo

    Stutter at 3500rpm only

    How would you diagnose what the issue is if it isn't throwing a code?
  5. BrinkExpo

    Stutter at 3500rpm only

    Hey guys I have an 06 Expedition with 155k on it. I just did the plugs and 3 coils 10k miles ago. The truck runs great but under WOT at 3500rpms it stutters and then it winds out good after it gets past the stutter. If I hammer down and it downshifts higher than 3500rpms it doesn't stutter. If...
  6. BrinkExpo

    Engine Ticking

    The tick/rattle is coming from inside the motor. I figured if I am hearing the timing chain or cam phaser rattle or both it is probably a good thing to fix so it doesn't cause any damage. Don't you guys agree?
  7. BrinkExpo

    Engine Ticking

    Thanks a lot for your help, I'll definitely do the lockout. Does anyone on the forum have the tune for the cam phaser lockout? I have the SCT tuner. Just need the tune. Also is there a way on the forum to find people in the twin cities that work on these Expeditions?
  8. BrinkExpo

    Engine Ticking

    He had a 2004 with 395,000 miles on it and to my knowledge he never had to do cam phasers or timing chain. Now he has a 2010 that he bought with very low miles on it. I am having a hard time selling it because of the work I have done recently. Transmission, $1,500 in body work(including core...
  9. BrinkExpo

    Engine Ticking

    At how many miles are guys usually having to do this? My old man has a 3v 5.4 with 250k on his and has never done cam phasers or timing chain
  10. BrinkExpo

    Engine Ticking

    Thanks, I have Ford semi synthetic 5w20 oil with Ford oil filter. Is that pretty spendy labor to do the timing chain or cam phasers? Looks like parts are around $200 for each kit.
  11. BrinkExpo

    Engine Ticking

    My 06 Expedition with 150k miles runs great. However if I rev the motor quick in neutral or if I give it a quick acceleration in drive or reverse, the motor makes a ticking/rattling sound like something is loose in there. It only does this at the lower RPMs and then goes away at higher RPMs. If...
  12. BrinkExpo

    Code P2106 & P2135 Truck Died

    Thanks for all the replies and PMs. I brought it to the dealer because of the lack of tools I have and they said to replace the entire throttle body. They warned me that when just replacing one sensor, they get around a 50% return rate for the other sensor or the throttle body going bad as...
  13. BrinkExpo

    Code P2106 & P2135 Truck Died

    What part are you talking when you say replace the throttle control? The throttle position sensor? The throttle body motor? Other?
  14. BrinkExpo

    Code P2106 & P2135 Truck Died

    Thanks for the help guys, it is a 2006 Expedition Limited, sorry for not providing that. What about the Fuel Pump Driver Module too? I have read people having similar experiences because the FPDM was so corroded. Thoughts?
  15. BrinkExpo

    Code P2106 & P2135 Truck Died

    Hey guys the truck died on the side of the road the other day. I got to the side of the road, started it back up, drove for about 10 seconds and then it died again and wouldn't start. I waited about 15 minutes, then the truck started back up and I drove it 15 minutes home and it seemed to run...
  16. BrinkExpo

    Oh no, it's back again

    Hey guys I posted a few weeks back a squeaking noise coming from underneath my 06 Expedition. Turns out it was the valve body. This was the 4th one in less than 5k miles! 1st one made the first to second shift hard. 2nd one made the squeaking noise. 3rd one was faulty from the factory so not...
  17. BrinkExpo

    Expedition Squeaking Noise? Video Attached

    Update: This noise was the valve body. This new tranny is now on the 4th valve body. 1st one made the 1st to second shift hard. 2nd one made the squeaking noise. 3rd one was faulty from the factory. The 4th one should be good now Good thing I have a 3 year warranty
  18. BrinkExpo

    White 06 Limited with black wheels

    No I don't plan on lifting. I don't like how the rear wheels look like they sit forward when you lift them. I just tuned it with an SCT tuner and I want to get a little more sound out of it but haven't decided which way to go for a muffler.
  19. BrinkExpo

    Dump Exhaust DIY

    Great, you should post the video with your new muffler
  20. BrinkExpo

    White 06 Limited with black wheels

    Put 2007 Expedition 18" wheels on after blacking them out. What do you guys think?
  21. BrinkExpo

    Dump Exhaust DIY

    Did you just remove that rubber exhaust hanger then since the tip is much shorter or did you re attach it? Also if the truck is parked, does the exhaust come up into the truck since it is dumping under the truck?
  22. BrinkExpo

    P1867 Transfer Case Plate Circuit

    Thanks for the response. What is pinpoint test K? When I click on it it says the requested page could not be found.
  23. BrinkExpo

    P1867 Transfer Case Plate Circuit

    Hey guys my 4WD is pulling this code and my truck will not go into four wheel drive. Does this sound like it is the 4WD shift motor that needs to be replaced? Any other ideas? Thanks
  24. BrinkExpo

    Dump Exhaust DIY

    Did you get a better sound from this or did you just do it for looks?
  25. BrinkExpo

    06 Expo No 4hi/lo and A4WD clicks

    I plugged in a scanner and the C1998 code pulled and it says "check advancetrac" on the dash now. Could this be why the 4x4 isn't working as it should? Advancetrac needs to be recalibrated?

Latest posts

Staff online

Members online

Total: 2,341 (members: 20, guests: 2,321)

Forum statistics

Threads
57,010
Posts
535,857
Members
54,703
Latest member
Bluey

Share this page

Top