Thank you for the picture and advice.
I want to put SS's on my Expy because I am running oversized tires and the fact that in most cases when there is a front tire blow-out, the vehicles first response is to veer hard in the direction of the blown tire.
The steering stabilizer is the most...
First off, thank you in advance.
I've been hunting for a steering stabilizer for my Expo but cannot locate a kit readily made and manufactured for her.
Has anyone successfully used a kit from say, an F-150 or Super Duty or any other vehicle for that matter?
If so, what kit?
It stutters at idle. It misfires random cylinders or can also throw specific to 3, 5 or 7. The CEL will go from solid on to flashing.
Also, it will suddenly clear up, run strong for about 50 miles then start back up from a slight stutter at idle.
The current codes are:
P0300
P0305
P0307
I have a 2003 5.4 with a chronic misfire I can't get rid of.
I found out that the culprit could be the VCT Sensor but upon calling Ford, I'm advised that the VCT Sensors didn't hit the 5.4 until 2005.
I'm not sure if this is accurate though as I can lookup and find VCT sensors for a...
I have a 2WD 5.4 EB 2nd gen Expo that is throwing three strange codes.
B1B<D - Body
B2TAE - Body
ROR -
I do NOT have air suspension nor did the truck ever have it and was converted.
SO..... What the hey?! Any ideas?
That is all feasible but I'm in Dallas/FtWorth so the environmental issues shouldn't be a variable.
I will explore the gasket/crack option (unfortunately).
I only got to pull 1, 2, 5 & 6 but again, #5 was under a layer of moisture and rust was everywhere in the spark plug hole.
#1 and 2 had corrosion on the hex with a bit a moisture #2.
#5
Imgur: The most awesome images on the Internet
Imgur: The most awesome images on the Internet
Imgur...
If POLY bushings were used in place or rubber ones, they MUST be lubed well upon install as they are grippy and will creak if not lubed. So much so that Energy Suspension uses lube fittings on some applications.
I noticed that the rear passenger window was making a grinding noise when put down but mostly when rolled back up.
I figured it may be some dirt somehow got in the rail of the regulator and just needed to be cleaned and greased.
However, upon disassembly I found that there isn't a traditional...
Bedrck47, how do I make payment towards the manual and wiring data?
Also, where is the other end of the harness from the TRS? I checked the wiring on the sensor side and it looks fine.
http://imgur.com/WyrzBRQ
http://imgur.com/n4CM9hG
I'm thinking about picking one of these up as well. Anyone have any experience with these or a competing product?
Bosch OBD 1050 | Mobile Scan Diagnostics Tool
Thank you Stamp. Yes, I've been rooting through forums and YouTube and also saw info that the harness at either end (but most likely the sensor end) can corrode, especially if the vehicle came from the East Coast and mine was originally purchased in Maryland so it's a possibility with mine.
Can anyone please advise as to where the Transmission Range Sensor is located so I can swap it out.
I have random misfire codes being thrown AFTER already replacing all eight plugs and coils.
I did have an instance where the OD light came on flashing but went away after I shut down the truck...
I'm confused now (Although, thank you for your reply) because I heard/read that 285's fit a stock 2WD but if 275's rub on a 4WD then what can be expected from the 285's
I am needing to replace the tires on my '03 Expo and have read that LT285/70R17's fit without any rubbing.
Anyone put this size on their 2WD EB?
I'm also considering General Grabber AT2 for the rubber.
Anyone have these on their Expo and what is your opinion?
Wear well?
Handling?
Wet...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.