Lightnig
Full Access Members
Installed my new billet grille
That looks really good.
Been thinking about doing the exact same thing to mine.
What brand insert is that?
What did you do to the expy today
- Thread starter cleaningman94
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
That looks really good.
Been thinking about doing the exact same thing to mine.
What brand insert is that?
Lightnig
Full Access Members
remounted my brush guard and winch.
Still need to rewire it, the P.O. did a piss poor job of connecting the battery terminals... grrr
Still need to rewire it, the P.O. did a piss poor job of connecting the battery terminals... grrr
superexpy
Full Access Members
Took her out and cruzed for new baby's moms.....
xtinc7ion
Full Access Members
Hey Lightnig, thanks, I am very happy with it. The kit I got was just one of the brands on eBay.
99 02 Ford Expedition Billet Grille Bumper 00 01 Combo | eBay
Nothing fancy, but it is very sturdy and went in pretty easily. Let me know if you have any questions!
99 02 Ford Expedition Billet Grille Bumper 00 01 Combo | eBay
Nothing fancy, but it is very sturdy and went in pretty easily. Let me know if you have any questions!
As an eBay Associate we earn from qualifying purchases.
superexpy
Full Access Members
I got bored and removed my rear windshield wiper and other stuff. Insted of painting I wraped it with white carbon fiber.
Was
And I did this
Was
And I did this
GAINMOB
Full Access Members
looks good
alaskanexpy
Full Access Members
mine took out a van's 2 doors day before yesterday. no damage to the expy though. the other half needs to learn how to drive/park though! ugh!
I think. I don't know what to think.
The dealership I got my ride from had a 5000 mile extended warranty on her. Had them look at the siphon filter or clean the tank because below 1/4 a tank but before the low fuel light, if I made sharp turns or suddenly stopped then accelerated she would die unless I pumped her pedal rapidly to feed her fuel.
Day one , I call in the morning, dealer says outside shop who does repairs can't find anything wrong, I offered to drive down during my work day to emphasize the problem. The dealer stated he would have them look into things further. I call later that day, the dealer states that the mechanic took a sharp turn and she began to act up, he informs me they are dropping the tank and going to check the siphon filter on the pump for debris. I call later that afternoon, the dealer states that there was a clogged filter on the pump and that they cleaned the tank . Unfortunately for the mechanic, the filter fell off the pump in the tank and more debris was sucked into the pump causing it to seize up. Free fuel pump for me, the dealer states she'll be ready by tomorrow morning.
Day two; I receive two phone calls from the dealer in the morning, he tells me both my upper and lower ball joints need to be replaced and since I'm there and already paying my fifty dollar deductible would I have he time to let them replace them? I oblige and keep my fingers crossed that I don't incur some hidden fees.
Later that afternoon I call to check on the status of my ride. The dealer states the ball joints were almost done however, oreily auto parts sent them a defective fuel pump. The new fuel pump would not be in until the next morning. I'm copesetic, who can complain when you're getting a 1000 dollar job done for 50 bucks?
Day;3 5/9/13- I call at 12. Tank is being lifted back into place , I should have her by lunch time. It's been a roller coaster ride of events but if 50 dollars is my end, I'm still stoked.
The dealership I got my ride from had a 5000 mile extended warranty on her. Had them look at the siphon filter or clean the tank because below 1/4 a tank but before the low fuel light, if I made sharp turns or suddenly stopped then accelerated she would die unless I pumped her pedal rapidly to feed her fuel.
Day one , I call in the morning, dealer says outside shop who does repairs can't find anything wrong, I offered to drive down during my work day to emphasize the problem. The dealer stated he would have them look into things further. I call later that day, the dealer states that the mechanic took a sharp turn and she began to act up, he informs me they are dropping the tank and going to check the siphon filter on the pump for debris. I call later that afternoon, the dealer states that there was a clogged filter on the pump and that they cleaned the tank . Unfortunately for the mechanic, the filter fell off the pump in the tank and more debris was sucked into the pump causing it to seize up. Free fuel pump for me, the dealer states she'll be ready by tomorrow morning.
Day two; I receive two phone calls from the dealer in the morning, he tells me both my upper and lower ball joints need to be replaced and since I'm there and already paying my fifty dollar deductible would I have he time to let them replace them? I oblige and keep my fingers crossed that I don't incur some hidden fees.
Later that afternoon I call to check on the status of my ride. The dealer states the ball joints were almost done however, oreily auto parts sent them a defective fuel pump. The new fuel pump would not be in until the next morning. I'm copesetic, who can complain when you're getting a 1000 dollar job done for 50 bucks?
Day;3 5/9/13- I call at 12. Tank is being lifted back into place , I should have her by lunch time. It's been a roller coaster ride of events but if 50 dollars is my end, I'm still stoked.
Lightnig
Full Access Members
Not today, but Yesterday
As a follow up to my dash light upgrade, I updated the lights in the HVAC controls. It's amazing, now I can see all the settings on the dial.
Can't believe the difference a simple bulb(s) change made...
If anyone else is tired of dim dash lights, I can strongly endorse a brighter set of lights as a very easy upgrade that is very noticable
As a follow up to my dash light upgrade, I updated the lights in the HVAC controls. It's amazing, now I can see all the settings on the dial.
Can't believe the difference a simple bulb(s) change made...
If anyone else is tired of dim dash lights, I can strongly endorse a brighter set of lights as a very easy upgrade that is very noticable
FordandPolaris
Full Access Members
Funny you say that, the only problem I have ever had with O'Reilly is when they sent us the incorrect fuel pump for our application. They sent us a pump designed for fuel injection when we needed a low psi one for a carb setup in our boat. Needless to say we were spraying fuel right past the needle haha.
alaskanexpy
Full Access Members
i hauled scrap steel to the recycler with the expy. 9,400 lbs combined with the expedition and trailer. truck handled great!
Just thought I would share what I did today.
First I added a cold air intake custom built went from factory intake with some small mods to all aluminum 4 1/2 inch pipe with a 10 inch filter I can definitely feel the power gain when I punch it. Now im just waiting to see if it helped my mpgs. Then i got rid of the factory running boards and installed some bully black bull aluminum side steps.
( i cant seem to get the pics to upload on here )
First I added a cold air intake custom built went from factory intake with some small mods to all aluminum 4 1/2 inch pipe with a 10 inch filter I can definitely feel the power gain when I punch it. Now im just waiting to see if it helped my mpgs. Then i got rid of the factory running boards and installed some bully black bull aluminum side steps.
( i cant seem to get the pics to upload on here )
Edmund K
Full Access Members
Very nice!
00EddieExpy
Active Member
Removed the headlamp switch and did the fog light upgrade as described in an old thread on the Lightning forum, now my fogs come on in the autolamp position like my Jeep GC used to. Snowball project, put frog tape under switch to protect dash while prying out the switch and noticed later that the tape must have lifted some of the tan, so off to the local autobody supply for some SEM dye to fix the black spots..........I usually can't leave well enough alone
Last edited:
mocrawlin
Member
put pmt lower control arms on! now i gotta order the uppers soon.
Mikes05expy
Full Access Members
New front pads & rotors, no more steering wheel vibration WOOHOO!!!
Sent from my Bag Phone using Tapatalk
Sent from my Bag Phone using Tapatalk
Mikes05expy
Full Access Members
Similar threads
