Search results

  1. C

    2000 expy 5.4L eddie bauer 4x4 279k 02 sensor data, is it bad?

    With the engine on: long term trim (1) -21.9 Long term trim (2) -14.1 St trim (1) -7.0 St trim (2) -3.9 St trim (11) -5 5 St trim (21) -3.1
  2. C

    2000 expy 5.4L eddie bauer 4x4 279k 02 sensor data, is it bad?

    Those readings above are with the engine off, key on
  3. C

    2000 expy 5.4L eddie bauer 4x4 279k 02 sensor data, is it bad?

    Hi everyone, I am having rich condition with my expy, code is po175. I changed my fuel injectors and cop's. I used my scan tool to check the data form the truck and this is what I found. my question is does this mean my o2 sensors are bad? thank you.
  4. C

    does anyone know how ot repair or replace this?

    that option with cutting off the bottom of it sounds like a good idea!! Ill let you guys know how it go's. thank you very much
  5. C

    does anyone know how ot repair or replace this?

    that is the stop for the bump stopper on the lower control arm.
  6. C

    does anyone know how ot repair or replace this?

    Thanks Bob, I am hoping someone has a easier fix, lol. I dont know how to weld or what plate to use. I would have to find someone who is able to do that and know what kind of plate to use.
  7. C

    High mileage Expys?

    280k here 5.4L, 2000 eddie bauer expy
  8. C

    does anyone know how ot repair or replace this?

    this part of my 2000 eddie bauer expy 4wd 5.4L. has busted, and caused the boot on my upper control arm to tear apart. does anyone know how to repair or replace these since they are welded onto the frame? thanks.
  9. C

    Steering gear box removal 5.4 4x4

    I used a torch, pb blaster banging on it with my mini sledge. bent my pitman puller. tried to get the pitman arm off the drag link, but that was a pain and it didnt come off even tho i used a tie rod puller...it started to bend. I a leaving the pitman arm puller on and torqued really tight and...
  10. C

    Steering gear box removal 5.4 4x4

    Yea i didnt want to use the pickle fork because of the boot, but i did get my pitman arm puller on and i have be turning in until the hooks end start bending around the pitman arm. several shots of pb blaster and it still wont come loose but my puller is bending....smh
  11. C

    Steering gear box removal 5.4 4x4

    Can anyone tell me the best way to get the pitman arm off the drag link. Its a 2000 expy eddiebaur 4x4, 5.4L. I amcrammed for space, thought about a pickle for but dont want to destroy the boot. Icant remove the arm fromthe gear box because i have no room for the seperator. Thanks in advance.
  12. C

    exhaust manifold stud ideas

    Hey guys i got my passenger side exhaust manifold off my 00 expy 5.4 4wd i have gotten all the stud and both exhaust flange bolts off without a problem until now, i have 3 studs left in the cylinder head they are sticking out alittle more than 1/2 inch out of the head without the nut . i tried...
  13. C

    AC clutch harness no voltage

    how do i "draw down" a vacuum
  14. C

    AC clutch harness no voltage

    how do i know if my switch i bad? or should i just go ahead and replace it?
  15. C

    AC clutch harness no voltage

    ok thxs a lot guys i jumped the harness and the clutch kick in and started spinning.
  16. C

    AC clutch harness no voltage

    i checked the low pressure switched for voltage and it gets voltage on the red w/wht side but not the other so i take it that must be ground.
  17. C

    AC clutch harness no voltage

    i checked the level with a coolant gauge, and where can i find the low pressure switch? i check everything that captain morgan responded with (this Cap).
  18. C

    AC clutch harness no voltage

    hey guys i have a 00 expo 5.4 4x4 and i am trying to get my ac clutch to engage but haven't had any luck so far. i have checked all the fuses and none are blown, i switched diodes nothing, i unplugged the clutch harness at the compressor and put my meter on it and got no voltage while on max ac...
  19. C

    mods tested on trip from florida

    Hi guys i just came back from my road trip to florida and i have to tell you the mods i have made on my baby gave me a 2mpg difference. before i went i had stock everything on my 00 expy eddie bauer 5.4 4x4, on the way down south i avg 13-14 mpg. when i got to florida i decided to make some mods...
  20. C

    ngk plugs?

    Ok I put in the Ngks and all I can say is wow... My expy runs so much more steady and smooth the car has get up and go. the old plugs weren't even bad looking, but ngks those plugs are amazing so.. From now on I will be using ngks in both my cars from now on. Now I just need to squeeze all the...
  21. C

    ngk plugs?

    ok i just got the ngk tr55gp platinums, i will try them in my 2000 5.4 and see how they do....i will post my opinion soon.
  22. C

    ngk plugs?

    wow NascarMike thats the first time i have heard about using copper plugs....what you say does make sense though. anyone else tried copper plugs???
  23. C

    ngk plugs?

    ok i will use them in my 00 exp, wheni went to autozone they told me that i had to use the iridium or the platinum ngk plugs, they said if i use the regular plugs i will have problems because the 5.4 engine gets too hot??? i have never heard this is it true or was he trying to make some extra bucks?
  24. C

    ngk plugs?

    Hey guys i wanted to know if any of you have used NGK plugs in your Expy's and if you did do you like them and which type of plug? i hear they are good plugs?

Latest posts

Members online

Total: 2,484 (members: 4, guests: 2,480)

Forum statistics

Threads
57,010
Posts
535,851
Members
54,700
Latest member
RyanStroeder

Share this page

Top