I will tomorrow .
The only tools needed is a Sawsaw and a 2lb hammer..lol
Sent from my Nexus 6P using Tapatalk
What did you do to the expy today
- Thread starter cleaningman94
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
The only tools needed is a Sawsaw and a 2lb hammer..lol
Sent from my Nexus 6P using Tapatalk
1955moose
Full Access Members
- Joined
- Nov 23, 2014
- Posts
- 6,004
- Reaction score
- 1,351
I know you guys are going to hate me, but San Francisco hit over 73 degrees today! Went to right outside ocean beach about 4:00 pm, had to put on sun block! You guys have got to go west young men!
Sent from my N9131 using Tapatalk
Sent from my N9131 using Tapatalk
USMCBuckWild
Full Access Members
It is easy to verify. The control unit for both seats is under the passenger seat. Pull the seat as far forward as it goes, the controller is a 3”x5.5” box that is mounted vertically on the back of the plastic piece that sticks down under the seat. It has 3 connectors (2 of them are small and have separate locks on them), the LARGE connector is the one in question. Disconnect it look at the pins/females, pin “M” is the ground (its M designator is cast into the controller). The pin directly next to it (empty in the pigtail) is the one that you add a female pin to and then splice into the ground wire coming from M.
Justinsteg
Member
Here my Rig sits after the 2" Wheel spacers
Sent from my Nexus 6P using Tapatalk
Scoot, how do you like those RBP tires?
No complaints I'd buy them again fo sure.
And they do real good in mud pits where the mud water comes in ya doors .hahaha
Sent from my Nexus 6P using Tapatalk
Looks hilarious with those skinny ass tires bro. Definitely a buck-tooth bob jobHere my Rig sits after the 2" Wheel spacers
Sent from my Nexus 6P using Tapatalk
ExpeditionAndy
Full Access Members
Would love to see a side view. Where did have to cut the wheel wells.
I'll post today it's really not as extreme as I probably made it sound but definitely involved cutting the Fender's and pinch weld seams inside the wheel well.
Sent from my Nexus 6P using Tapatalk
Slight angle at right side bottom corner .
And up the pinch weld seams line cut that and beat it over so that the rough edge doesn't get a chance to cut into my tires.
Tomorrow I'm gonna put it back on the lift and take off the front tires so that I can make it look less hacked up.
Sent from my Nexus 6P using Tapatalk
HereSlight angle at right side bottom corner .
And up the pinch weld seams line cut that and beat it over so that the rough edge doesn't get a chance to cut into my tires.
Tomorrow I'm gonna put it back on the lift and take off the front tires so that I can make it look less hacked up.
Sent from my Nexus 6P using Tapatalk
Sent from my Nexus 6P using Tapatalk
ExpeditionAndy
Full Access Members
Okay I see what did now. Very cool. I think it looks good. How does it handle on the highway?
Handle like a beast I can take curves way faster and don't feel that heavy feeling trying to roll over while in the curves..
And doesn't feel top heavy like B4..lol
I like it
Nice feeling going around curves and don't feel like u gonna roll over...hahah
Sent from my Nexus 6P using Tapatalk
MattG.in.LA
Member
Leveled mine out ... Anyone got an extra lsd carrier for the 9.75 rear 
Sent from my XT1650 using Tapatalk
Sent from my XT1650 using Tapatalk
ExpeditionAndy
Full Access Members
Very cool!
Can’t even tell unless u r looking at it.
Similar threads
