Search results
-
1st gen sub and box
I have a factory 8" sub in box out of my 2000 EB. Not real sure whatbits worth sos hoot offers. Looking to get around $50 o.b.o. plus shipping. -
Shaking and hasitating
Just spray along all vacuum lines and if u have a hole in a line it will suck in the wd-40 and idle will jump up- EXPI2000
- Post #7
- Forum: 2nd Gen - 2003 - 2006
-
Shaking and hasitating
U can spray wd-40 along your vacuum lines and if your engine revs at anytime then u have a vacuum leak at that point...just make sure u arent soaking it in it lol- EXPI2000
- Post #3
- Forum: 2nd Gen - 2003 - 2006
-
What did you do to your expedition today?
Installed 8 new spark plugs, new fuel filter, a vacuum line and 2 MAF sensors since the first one was apparently junk. Truck runs smoother now for sure and gonna sea foam it next few days.- EXPI2000
- Post #80
- Forum: 1st Gen - 1997 - 2002
-
brake caliper bolts ?
Its a t45 torx bit...like stamp said just buy a set lol Sent from my Samsung Galaxy Tab 2 using Tapatalk now Free- EXPI2000
- Post #3
- Forum: 1st Gen - 1997 - 2002
-
steering wheel wiggles
My steering wheel had play in it a while back. Took center off and seen it was oblonged where the wheel sits onbthe shaft. Went to pic a part and grabbed a wheel from an f150 and no problems since. Sent from my Samsung Galaxy Tab 2 using Tapatalk- EXPI2000
- Post #5
- Forum: 1st Gen - 1997 - 2002
-
New Member from Indiana
Welcome...nice to see someone else from Indiana lol. Sent from my Samsung Galaxy Tab 2 using Tapatalk- EXPI2000
- Post #3
- Forum: New Member Check-In
-
99XLT - Build Thread (many pictures)
Looks good so far...keep up the good work. Really like those headlights Sent from my Samsung Galaxy Tab 2 using Tapatalk- EXPI2000
- Post #5
- Forum: 1st Gen - 1997 - 2002
-
Plasti-Dip questions
I did all my tan trim and rims on mine. When I did my rims I drove about an hour after I finished and no problems. Only problem areas I've had are the running boards because my kids climb in and out with their cleats on and that tears it up over time. Other than that its held up quite well over... -
2000 EB with Mach Audio System - Specifications?
I have a 2000 eb also and there are 6x8 in the four doors and an 8" sub in the back right by the third row seat. The rear sub should also have the factory amp attached to the box in there. Sent from my Samsung Galaxy Tab 2 using Tapatalk- EXPI2000
- Post #2
- Forum: Audio & Electronics
-
tires?
I have cooper discovery atp 285/70/17...no dip in my fuel mileage and they ride well...took them all the way to Florida and back and are fairly quiet...I lije them a lot and did real well thru anything I've put them thru so far. Sent from my Samsung Galaxy Tab 2 using Tapatalk- EXPI2000
- Post #5
- Forum: 1st Gen - 1997 - 2002
-
Amp and sub install 02 EB
I know I'm late to see this but I just did this. I tapped my inline converter to the left and right front speaker wires on tge main harness for the radio. Also I tapped remote wire into power wire on same harness and ran it to amp. I hope tgis helps. Sent from my Samsung Galaxy Tab 2 using...- EXPI2000
- Post #3
- Forum: Audio & Electronics
-
Plasti Dip Mayhem phase 1
My ford emblems are flat black on front and back but I left the expedition emblems chrome on the side to flow with other chrome I left on truck Sent from my Samsung Galaxy Tab 2 using Tapatalk -
Dash lights are out!
What year is your truck??? Instrument illumination fuse number 18...but I have a gen 1 Sent from my Samsung Galaxy Tab 2 using Tapatalk- EXPI2000
- Post #2
- Forum: Electrical
-
Got bored so I picked up my airbrush...
Looks good Sent from my Samsung Galaxy Tab 2 using Tapatalk -
Tires ??? Should I
I like the look of them but don't know anything about them...read the results of their test runs you posted and they only expect 20, 000 miles out of them??? Sent from my Samsung Galaxy Tab 2 using Tapatalk- EXPI2000
- Post #4
- Forum: General Discussion
-
Plasti Dip Mayhem phase 1
Yeah I like mine being flat black cause it blends in but you can still see it Sent from my Samsung Galaxy Tab 2 using Tapatalk -
Plasti Dip Mayhem phase 1
They look damn near identical lol....sorry just didn't like the look of all the other fonts avail able most made it too hard to read -
did some dip today
I did my rims and left them on tge truck when u did it. Like forandpolaris said just make sure u clean any debris off your rims first. I did use an old sheet and wrapped my rotors and calipers. Had some minor overspray on my tires but was not noticeable at all. Sent from my Samsung Galaxy Tab...- EXPI2000
- Post #3
- Forum: General Discussion
-
need help getting starter out
I rldid mine a few months ago..to get to the top bolt I had to use about a foot of extensions on the socket wrench. Just come from the end and guide the socket over the top of the starter. I could only get about a quarter turn at a time if I remember correctly. Good luck and hope this helps...- EXPI2000
- Post #2
- Forum: 1st Gen - 1997 - 2002
-
Plasti Dip Mayhem phase 1
Thx guys Sent from my Samsung Galaxy Tab 2 using Tapatalk -
Plasti Dip Mayhem phase 1
Finally got all tye tan trim painted black...now job will be saving up for a system to throw in it Sent from my Samsung Galaxy Tab 2 using Tapatalk -
Painted bumpers
Stick with the white...looks better for the style of your truck...just my opinion. Sent from my Samsung Galaxy Tab 2 using Tapatalk- EXPI2000
- Post #4
- Forum: 1st Gen - 1997 - 2002
-
No tail lights
Well I finally tracked down tge problem. I followed all wiring from tail light forward. So when I got to the wiring inside the truck under tge carpet I noticed my running board lights were go off if I moved the wiring. So I removed some of the covering on the harness to discover that where tge...- EXPI2000
- Post #7
- Forum: Electrical
-
Taillight Tinting
I used VHT Nightshades and put on 3 coats on my tails. You can see them perfect in daylight too. I also did no prep work other than wiping dust and dirt off them. Turned out pretty well and has held up well even in many carwashes. Sent from my Samsung Galaxy Tab 2 using Tapatalk
