Search results
-
J
P0304 wont go away can it be a Cat?
Assuming you replaced plug when you did the CoP?- Jason_CPAPS
- Post #2
- Forum: 1st Gen - 1997 - 2002
-
J
Painted bumpers
The white looks better. To me chrome and white dont mesh well- Jason_CPAPS
- Post #5
- Forum: 1st Gen - 1997 - 2002
-
J
white resedue after wet sanding
Dont have a buffer jay. I spent about 5 min on the fender witj some cheap compound and blue shop towels. Came out to my liking. After all I didnt go od green to impress anyone but more so concealment if shtf with all tje gun talk.- Jason_CPAPS
- Post #9
- Forum: 1st Gen - 1997 - 2002
-
J
Help smoke on start up
Lucas doesnt make a bad product imo- Jason_CPAPS
- Post #7
- Forum: 1st Gen - 1997 - 2002
-
J
white resedue after wet sanding
As always thanks everyone- Jason_CPAPS
- Post #7
- Forum: 1st Gen - 1997 - 2002
-
J
white resedue after wet sanding
Not sure but I painted it outside so it came out rough amd the clear was labeled flat but came out more glossy than I like- Jason_CPAPS
- Post #5
- Forum: 1st Gen - 1997 - 2002
-
J
white resedue after wet sanding
So I painted my expy od green and sparyed a flat clear for protection. Am in the process of wet sanding. There is a white resedue now. Do I get rid of it by polishing? If so can I polish without a buffee abd what polish should I get- Jason_CPAPS
- Thread
- Replies: 8
- Forum: 1st Gen - 1997 - 2002
-
J
Safari Bar?
I thought about putting a black one on my od green expy but decided to build a bumper out of 1 in c channel- Jason_CPAPS
- Post #4
- Forum: 3rd Gen - 2007 - 2017
-
J
can someone please help???
When I got my expy I had the same isssues. Replace the coils. I got from summit. They work just fine, my cats were completly melted now they are gutted, dedd feed back pressure, egr valvr and some sensor near egr, cleaned maf, replaced 2 vac lines and the line amd elbow that runs to back...- Jason_CPAPS
- Post #14
- Forum: 1st Gen - 1997 - 2002
-
J
used runing boards off 97 xlt
Nobody need running boards? Cash is king but will trade as well- Jason_CPAPS
- Post #2
- Forum: For Sale
-
J
used runing boards off 97 xlt
Took my running boards off my expy. No intention of putting back on. Make me an offer. L9cation carlisle pa- Jason_CPAPS
- Thread
- Replies: 1
- Forum: For Sale
-
J
New member, have a few questions (EASY IM SURE)
Stamp we use the old race on semis however the ones on cars and trucks drive much easier. I use a soft cold rolles steel race punch to get them out at work. Have used a screw driver on lighter vehicles. However if uve never replaced races dont use a screwdriver. You could scar the hub- Jason_CPAPS
- Post #10
- Forum: 1st Gen - 1997 - 2002
-
J
catalytic converter help please
If they dont use a sniffer in ur state cut the xats and move o2s out of stream.- Jason_CPAPS
- Post #9
- Forum: 2nd Gen - 2003 - 2006
-
J
New member, have a few questions (EASY IM SURE)
I wouldnt replace a bearing without replacing a race. If one is worn or marked so is the other- Jason_CPAPS
- Post #7
- Forum: 1st Gen - 1997 - 2002
-
J
Broke bolt for coil pack?
If sezied hit it with map gas or propane. Be careful tho. Id prob drive that sum bitch- Jason_CPAPS
- Post #9
- Forum: Engine & Performance
-
J
Lower ball joint replacement 1998 Expedition
I think it the lowers on mine that can be replaced but not uppers. Mine is a 97 tho- Jason_CPAPS
- Post #2
- Forum: 1st Gen - 1997 - 2002
-
J
brush guard
Looking for a brush guard or push bumper. Not sure whick one yet. Prefer it black. For 97 expy- Jason_CPAPS
- Thread
- Replies: 3
- Forum: Wanted
-
J
painting expy
Easy enough. Ill just bring work truck home and weld er up- Jason_CPAPS
- Post #4
- Forum: 1st Gen - 1997 - 2002
Latest posts
-
-
-
2006 EB Rear HVAC Inoperable / Fuse, Relay, Resistor Good- Latest: 2006Overlander
-
