Anyone install a Readylift leveling kit?

[Chris Haraway]

I love the lift and clearance you guys are getting. I expected to install a leveling kit and airbags, but my stock rig is nuts on level with no load. I read somewhere there is a leveling system installed for towing, but yet to confirm.

 

[aggiegrad05]

That Stealth looks very nice. I am still confused about the CCD...it is part of the Stealth package with 22in wheels, but if you also add the Heavy Duty Tow package...doesn't that remove the CCD? It's not listed on my window sticker.

Unless something has changed since I bought my ‘18, if you have 22” wheels you have the CCD, end of story. The addition of HD Tow does not remove that. And my window sticker doesn’t list the CCD either, so apparently it’s not a window sticker worthy item.

 

[MATT0404]

Any suggestions on what size tire to run with this lift? I know the website says up to 35" with factory offset, but I'd like to run the wheels below. My main concern is allowing full suspension travel without any rubbing.

Preferred tire: Cooper Discoverer AT3 XLT



I'd like to run this wheel:

 

[16plati]

Any suggestions on what size tire to run with this lift? I know the website says up to 35" with factory offset, but I'd like to run the wheels below. My main concern is allowing full suspension travel without any rubbing.

Preferred tire: Cooper Discoverer AT3 XLT

View attachment 29213

I'd like to run this wheel:
View attachment 29217

Either 35/11.50/20s or 33/12.50/20 on STOCK wheels will work no rubbing or trimming. Put them on anything other than stock wheels and I can’t guarantee you’d have zero issues

 

[16plati]

Any suggestions on what size tire to run with this lift? I know the website says up to 35" with factory offset, but I'd like to run the wheels below. My main concern is allowing full suspension travel without any rubbing.

Preferred tire: Cooper Discoverer AT3 XLT

View attachment 29213

I'd like to run this wheel:
View attachment 29217

If you go +18s you will have a lot of rubbing On 35/11.50s. I have 35/11.50/20s on my 16 with 1.25” bora adapters and I have to trim a lot of the wheel well, fender, and move power running boards back. With the adapters, it’s basically like running a +12 over +44 wheel

 

[MATT0404]

Either 35/11.50/20s or 33/12.50/20 on STOCK wheels will work no rubbing or trimming. Put them on anything other than stock wheels and I can’t guarantee you’d have zero issues

If you go +18s you will have a lot of rubbing On 35/11.50s. I have 35/11.50/20s on my 16 with 1.25” bora adapters and I have to trim a lot of the wheel well, fender, and move power running boards back. With the adapters, it’s basically like running a +12 over +44 wheel

Good info. Thanks, guys. Might just stick with stock wheels for now.

 

[16plati]

Good info. Thanks, guys. Might just stick with stock wheels for now.

No worries, good luck in finding that perfect match for your truck!

 

[julijn]

There are two people that make the brackets needed that I am aware of. You also need to find a shop that is willing to work with a little trial and error.

Attached is our 19 stealth with CCD

Can you please show me who make the adapters? I am ready to buy them now.. got the readylift kit. Thank you.

 

[julijn]

Just wondering if these are the sensor links that need to be replaced when doing the lift on the ccd rides ???? Anyone that has it done can you post some pics of the stuff needed. It would be very helpful.

 

[julijn]

Just wondering if these are the sensor links that need to be replaced when doing the lift on the ccd rides ???? Anyone that has it done can you post some pics of the stuff needed. It would be very helpful.

View attachment 29248

The little I gathered is that I am correct that these are the height sensor brackets. ..the good thing is that I did the same with my 2015 grand Cherokee and made extras brackets. I just need to adjust to size...So now I have the readylift and the linkage brackets all that’s left is the fun part wheels and tires.

 

[julijn]

bumpity bump... anyone with the readylift kit on a platinum know if those are for sure
the links I need to adjust??

 

[16plati]

bumpity bump... anyone with the readylift kit on a platinum know if those are for sure
the links I need to adjust??

Have you contacted Readylift? They’ve had to have done one with those brackets, I would think

 

[Neil T Casey]

bumpity bump... anyone with the readylift kit on a platinum know if those are for sure
the links I need to adjust??

This is correct for the CCD. I am going to do mine in a couple months. I talked with MIEKK about this, he sells/makes adjustable links so you dont have to move the actual brackets. Should be pretty straight forward and from what I have seen jacking up the vehicle the adjustments are not too crazy for the 3/2 readylift setup.

 

[Tom T]

ReadyLift tells me "no Platinum version in the works", so all custom made ;-)

good stuff, guys

 

[julijn]

ReadyLift tells me "no Platinum version in the works", so all custom made ;-)

good stuff, guys

yes we kow that what is says on the package.. but its not hard to make those brackets to keep the sensors level.. that's all that needs to be done... I have an extra set I made 4 for my grand Cherokee air ride to lower that truck a little more...kept them and I know why now.. I just need to adjust them to size....I will post when I decide on rims and tires....

 

[James Alexander]

See attached for contact

 

[Tom T]

would this work as bracket?
https://www.bagriders.com/only-charged-dubs-universal-height-sensor-bracket-small-holes.html

@James Alexander is this your phone? do you do some brackets?
@Miekk do you sell brackets for the Platinum lift?

Does anybody have more photos of lifted 2018/19 Expeditions?

Thanks much

 

[PHIL NOWASKI]

 

[julijn]

View attachment 29912

would you mind giving wheel size.. they look like 35s? looks great.. how does it drive.. I have to pull the trigger on some rims then the tires.. I already got the ready lift...also can you show us the brackets? would be a great help.. it would help all future lifters....no one has shown them.. they look like the pics I posted earlier correct?

 

[julijn]

They look like this... adjustable size. easy to make.