Pipes, I want setups and prices

[01expy]

i like how aggressive soliders is im thinking a muffler delete and a y pipe to duals so thats what im thinking anyone know how much itd run for

 

[ZombieSoldier]

before you go get it, this is mine...

http://www.facebook.com/video/video.php?v=10150372381634863

 

[01expy]

didnt work

 

[gearhead847]

I just cut right before the muffler, pullex the tail pipe and muffler out from under the truck and slapped on a turndown tip for 7 bucks and called it good...its sounds very racecar like when i step on it. And since it dumps under the truck I dont have to worry about crushing any pipes

 

[TexasAngel34]

cut out the muffler, cats still in, added a reg pipe single, sounds freaking bad ass,, cost me $40 ...

 

[WHOISMOOTOO]

flowmaster 40-awesome
cut the tip and made a y pipe
around $200 El Paso (FT Bliss) labor..lol
http://youtu.be/DsCdxTMZPFM
http://youtu.be/dyfvIA4Sq3I

 

[toms89]

Well...I had a complete custom exhaust installed from my 1 5/8" shorties back. Dual stainless 3" with high flow cats into dual in and out magnaflow muffler with internal x-pipe. It was way too loud for my taste but it did sound very mean and deep. Sounded like a big block race car is how I would describe it but I had additional resonators installed after the muffler and it quieted it down to what I consider reasonable. Had them install v-clamp connectors so it could be removed for accessibility for tranny and etc..

It cost about $1100 complete but it is all stainless, mandrel bent and took over 8 hours of labor to install/fabricate.

If you watch my link with some decent headphones you get an idea what it sounds like. Turn it up but not too much as the blower is quite loud Drivers side window is down....

 

[LameSuburbanDad]

Magna-Flow single cat-back system. used, $100

really mellow and low tone, sounds best at 2,000-2,500 RPM

not aggressive or loud at all, just mellow rumbles, also there is no drone at cruising speed. probably NOT what you're looking for.

 

[Canadian Expy]

Gibson headers 2.5" duals back to a Magna flow muffler with dual 2.5" in and out with built in x pipe.Full SS with mandrel bends, chrome tips out the back. All 4 stock cats still in place, not real loud but a nice growl. may get louder when I remove rear cat and put pair of high flows in front

 

[Knautical2001]

Flow Master with 2" with chrom tips. Sounds great!! I am not at home, but once I get home from deployment I will post a vid. I still have the cats too. Picture is in my signature.

 

[Knautical2001]

But mine was pricey, $350, but they also had to go under my axle because of the indipendant suspension (sorry about the spelling, that is one thing I am NOT good at). LOL

 

[GAINMOB]

they also had to go under my axle because of the indipendant suspension

thats why i was told i couldnt get it...there are 2 guys that got it done...one lost the spare (not willing to do that) and the other went with smaller piping in order to get it around the IRS...if i had thought about it then...i couldve gotten it done for $175...since i didnt...$150 at local exhaust shop in Ft Walton Beach FL next to Eglin AFB...miss that place

 

[Knautical2001]

Yeah, I hate the ones that say they can't do it, it just means they are either A) too lazy to have to work, B) really don't know what they are doing or C) Have no imagination to be able to work it out. Either way, I found one that does so I am happy. I got all Stainless steel too so it is awesome. And I think I was wrong, I think I have 2.5" not 2". I can't remember off the top of my head.

 

[midsouthduck]

Mandrel bent 90 deg sections welded to flanges and connected to pipe after 2nd CATs. Ebay
RRE 2-1/2" dia, 1/2"thk DP flanges, gaskets. Road Race Engineering
Magnaflow 2x 2.5" into single 3" out TRU Y-pipe Transition, 2.5" & 3" u-bolts. Ebay
Flowmaster 70 series big block 3"in-3"out straight muffler w/heat shield from Ebay
Single Gibson 3" mandrel bent tailpipe from muffler (no SS tip). Gibson
McMaster Carr grade 8 bolts & nuts. McMaster
Muffler shop installation. Some place in Olive Branch, MS.
Total parts and labor $400.

Not too loud cause the wife drives the truck sometimes. I don't have to pass emissions where I live, but no change to Cats so should be OK.

 

[Expyguru]

Longtube ****** headers-cat delete all 4. Then straight pipe to turn downs. Headers 479.00 pipe 40.00 emission standards none loud extremely lol.